Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
We have an application where we have a large number of sensors, some relay nodes and one or more gateways. The sensors and relay nodes are provisioned by the gateways and...
Hi, I can normally log with NRF_LOG_INFO(). But if i enable softdevice (bluetooth stack init) logging stops working. Interesting part is that there are several log lines before...
BLE Control by Main CPU (MCU):
1. How the MCU communicates with BLE HW?
2. What is the amount of MCU performance is required to control the BLE? (expected answer example...
Hi nordic.
I use SDK 14.20 and nrf52840 board and s332 softdevice.
Our app has to use ant+ and ble.
My device connect with app.
App requests device to ant+ scanning...
hi guys:
When I was using mesh sdk, there was an error in compiling.
I use examples\light_switch\server\light_switch_server_nrf52832_xxAA_s132_6_0_0.emProject
I am...
Hi,
I am using SDK 14.2 -> BLE peripheral proximity example. I was trying to add a custom service and some characteristics to this proximity example. I basically took the...
Hi, I have two strange problems regarding the NRF_LOG. 1. In a for loop, char string that has changed is not printed out as what it contains now, it is printed out as what...
Hi,
i have purchased the following module
However, after connecting the VCC and GND to 3.3v DC supply the module is not detected. My questions are :-
Does...
how to slove it
1> Linking light_switch_proxy_server_nrf52832_xxAA_s132_6.0.0.elf 1> build/light_switch_proxy_server_nrf52832_xxAA_s132_6.0.0_Debug/obj/ses_nrf52840_Vectors...
I am using the nRF52832.
I want to go to sleep in absolute lowest power mode possible that still allows a timer for wakeup. Using LFINT.
I don't need ram retension, etc...
Code example: nRF5_SDK_15.2.0_9412b96\examples\peripheral\usbd_ble_uart_freertos
Board: custom board with nRF52840
What are the fastest and easiest steps to make this...
Hello,
I am trying to code nRF52840- DK with MAX30003 ECG Board Using SPI. I have referred Arduino Uno Code for MAX30003 ECG.
I need some help for Driver Development if...
Hi,
Is there a way to dynamically disable only the fork of a PPI channel or should I go through disable-free-alloc-assign sequence?
Will nrfx_ppi_channel_fork_assign...
