I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hi,
i am using ble_app_template and i added the file "ble_lbs.h" in the main file. Also added this code in the services_init method
uint32_t err_code;
ble_lbs_init_t...
Hello
I've been experiencing an unusual problem using the TWI/I2C library for the nRF51-DK board. Basically, I found that I need to shift my device address to the left...
Hi guys,
I have followed devzone.nordicsemi.com/.../ to set up CrossWorks. Even though I got pass the ble_stack_init();, I still can't discover the device for some reasons...
Hi
Please tell me someone me how to start nRF51822 & softdevice8.0.0
I build a NRF51822 application in gcc & ECLIPSE.
When to run the program, it crashes in the boot...
I'm having a problem adding the GPIOTE_IRQhandler() to my main.c file (see attached). I'm getting a compiler error that it is doubly defined in app_gpiote.o and main.o, but...
is it possible to update the pca20006 (rev. 1.2.0 2015.06) beacon with the pca10000 over DFU?
When i tried to update it with my application written for an older version ...
Hi folks,
I'm using the ble_app_template on a custom board. The BSP has a bunch of stuff I don't need, so I would prefer to not use it and handle my I/O directly instead...
i was going through TWI initialization process here i am confused why have we disabled Blocking mode. The reason for Disabling TWI_BlOCKING_DISABLED
I am referring the below...
hi , i want to modify the "transmitter_pca10028" and "receiver_pca10028" examples in SDK to obtain a transmitter/receiver in the same time (tranceiver). So someone have idea...
Hello, I am using the nrf51822EK and I want to combine the ADC and LPCOMP although in the reference manual it says they can not be used at the same time. Is it possible to...
Hi all,
I met one strange thing on SPI interrupt:
when 51822 advertising, the SPI write and read works well;
But, when CONNECTED, with BLE_GAP_EVT_CONNECTED event occured...
Hello,
I migrated my project from softdevice S110 7.1.0 on a nRF51422 FAC to softdevice S110 8.0.0 and an nRF51822 FAA G3. My code used to have a current consumption around...
Hello everyone,
I'm currently using and modifying the experimental_ble_app_uart. I've seen that for sending characters resp commands the file simple_get_uart is used. My...
