I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi
I'm trying to test UART over BLE using the nRF51-DK and the sample code "ble_app_uart_s110_pca10028 (nRF51 PCA10028)" along with both the nRF UART APP for both Android...
I'm using nRF51822 SoC , is it possible to change the major value when i push the button ? I tried simple assignment but it didn't work so i ask if i have to use the function...
hi,
i have kept RAM block 0 and RAM block 1 on in OFF mode by calling "sd_power_ramon_set(0xf000f)" before entering off mode ,i saw the value of RAMON register is 0x00030003...
I'm using nRF51822 SoC . I wanna read and write from the flash memory . Shall I use a specific configuration before using read and write functions provided from S110 softDevice...
we have created ble mesh, and data through ble nodes is passed every 5 seconds, but nodes gets disconnected with reason BLE_HCI_CONN_FAILED_TO_BE_ESTABLISHED??
please someone...
we have created ble mesh, and data through ble nodes is passed every 5 seconds, but nodes gets disconnected with reason BLE_HCI_REMOTE_USER_TERMINATED_CONNECTION??
please...
we have created ble mesh, and data through ble nodes is passed every 5 seconds, but nodes gets disconnected with reason BLE_HCI_CONNECTION_TIMEOUT?
please someone give...
we have created ble mesh, and data through ble nodes is passed every 5 seconds, but nodes gets disconnected with reason BLE_HCI_LOCAL_HOST_TERMINATED_CONNECTION?
please...
Hi all,
I am choosing a oscillator and my choice was a 16MHz stability +-9ppm, tolerance +-10ppm, 9pF
my FAE gave me the hint to use a 32MHz which is stability +-20ppm,...
Hi,
I have my BLE services arranged in different .c files. If I change anything in these files and compile (using Keil uVision 5) and load the program, it seems like the...
What is the designed (/actual/required due to the specification) behaviour of the Bluetooth stack S110 when notification packets are queued and the CCCD controlling the attribute...
I am looking into using Internal RC instead of External Oscillator (with softdevice on).
The function ser_app_hal_hw_init() uses Xtal clock source by default.
...
Hi, everyone. What is the meaning of datasheet "section 8.5.7 Antenna matching network requirements"->15+j85 ?
Whether is that we can caluate the 50o with the data?
