I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
I have reading lot of questions/answers about the nRF52840 and when asking for pricing and availability the answers is always "call to sales manager or distributor" , however...
Let's say we are running multiple state machines in a ble device, so that it can accept multiple connections in Slave roles. Will all the state machines share the same Advertising...
Hello,
I'm trying to measure battery voltage on nRF52832 chip using SAADC based on examples/peripheral/saadc and examples/ble_peripheral/ble_app_proximity and noticed that...
Hi I think this might be a potential bug in peer_data_storage.c
ret = fds_register(fds_evt_handler);
if (ret != NRF_SUCCESS)
{
return NRF_ERROR_INTERNAL;
}
ret = fds_init...
Dear All, I'm developing a connectionless beacon, it can be an observer or broadcaster device depending of time slot. But softdevice stack does not leave available space to...
I have an application that uses FDS and I've recently added to it the peer manager in SDK 12.2.0, which also uses FDS. It turns out that the application data keeps being updated...
Hi!
I have some questions with regards to the Philips Dual IR/RF remote (and other remotes) using Nordic Semiconductor components:
www.nordicsemi.com/.../Advanced-QWERTY...
Hello Nordic developers,
I have been unsuccessfully trying to use the extended ATT_MTU / DLE sizes for increased throughput on a nRF52832DK board running the Nordic UART...
Hi
I am working with nrf52 development Kit. Until now I have not worked with the whitelist advertising. I am using SDK v11.
I have a requirement initially I need to advertise...
Hello,
it seems the current nrfutils release assumes that the bootloader settings will be stored at address 0x7F000 on an nRF52.
However, unless I'm mistaken, that is...
Hi,
I have set up the Power Profiler as per the directions now on the step connecting the board to the Wiindows Python app it says "Cannot find calibration values" and the...
/* Copyright (c) 2012 ARM LIMITED
All rights reserved.
Redistribution and use in source and binary forms, with or without
modification, are permitted provided...
Hello,
I am trying to program my BMD-300 using the NRF52-DK, below are my connections
BMD- 300 ---------> NRF52 DK
V Vtg
SWDIO SWDIO
SWDCLK SWDCLK
GND GND
The BMD 300...
Hello friends. How to write a number to and read from internal flash. My information about the microcontroller is very weak. I use STM32F103RET6 .
I test The following program...
