It is nRF54L15 + SDK 3.0 + Matter application.
I have developed a custom BLE service that is based on Nordic's proprietary NUS BLE service. The BLE custom service is enabled...
I am trying to get a WiFi project working using the nRF52840DK and nRF7002EK . I use a 3.3V power source that is supplying power to both nRF's in parallel. For the nRF7002EK...
Hi,
I'm developing firmware for the nRF52840 DK using nRF Connect SDK v2.9.2 , and I’m running into a problem that didn’t occur in v2.8.0 .
My project uses Zephyr and...
I am receiving an error when connecting to a custom board by running nrfjprog --reset, any similarly with any other commands that require connection.
I am connecting through...
We have previously used nRF52840 and for the latest iteration of our board design we are updating to use nRF54L15.
We are aware that for nRF52840 we could map any pin to...
Hi,
I faced with an initialization issue of combination two features: MCUMGR and UART_ASYNC_API. I get a crash right after the FW starts. It looks like the SW configuration...
I checked the nrf52832 manual and found that both XC1 and CX2 are analog input pins for the 32Mhz clock pin configuration. The reference design for both uses 32Mhz crystals...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
I need to poll a NMEA data stream and it's easiest getting a byte at a time, but it's dropping to 30ms between individual reads in this loop:
uint8_t next = 0;
uint8_t...
Hi.
I'm working with the nRF51422 devlopement kit (pca10028) and I need to mesure the highest throughput between the nRF51 DK and a smartphone. I have seen several post...
I am using the heart rate example to do a quick demo. I am sending a short string of data one byte at a time to the iphone. I decreased the HEART_RATE_MEAS_INTERVAL interval...
Hi guys,
I have the nRF51 Development Kit, and I am trying to develop on my mac using GCC and eclipse. However, the tutorial I found either incomplete or outdated. I tried...
I want to bring up my own new board, but the nRFStudio can not connect to the J-Link, please check the picture.
I connect 4 lines from board to J-Link, including VCC, GND...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
I haven't seen any posts about this, so I thought I'd post what I observed and how I fixed it in the hope this helps someone else.
My nRF51 DK (PCA10028 v1.1.0) out of...
I have gone through most of the guides/links that I saw here to no end.
My development environment is OS X 10.9, gcc-arm 4.9, nRF51822 beacon.
Before going for the IDE...
Hi,
I am trying to build a low power device using the nRF51422 SoC without a Soft Device. I need a timer to occasionally wake up the chip and as I read the product specification...
I have a basic question regarding a basic area. Interrupts! But without any good specification and how the OS work and good example how to do this I need to push for the obvious...
In ble_dfu.c (unmodified SDK 8.0.0) I am unable to get the buttonless DFU hooked up.
For reference, ble_app_hrs with s110_with_dfu works correctly. I have traced my issue...
Hello,
I am trying to write data to flash with the pstorage api. I managed successful to write data to flash with the pstorage_test_store_and_update() function from the...
