At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
I downloaded nrfconnect-3.3.0-x86_64.AppImage from https://www.nordicsemi.com/Software-and-tools/Development-Tools/nRF-Connect-for-desktop/Download#infotabs .
I cannot start...
Hello,
I admit, that this is a bit of advertising for my open source mesh protocol, but I'm also curious if there is anybody that successfully compiled it and if there...
Hello,
I get an error fatal when running Heart rate collector example from SDK12 on PCA10040 development board.
The sensor use example from SDK15 on a nRF52840-DK.
Some...
Hi,
I want to use Segger Embedded Studio to write firmware for Thingy 52 but I don't know what programming hardware I need. Is there any documentation that supports Segger...
Hello,
Thank you for helping me to interface the Si7021 humidity and temperature sensor with Nordic nRF52 development kit board. I need to write the necessary code to finish...
Hi,
I am using nRF52832 for my development, I want to send 8 bit device ID as an advertising packet with company ID and Data.
Is thereany way to send the same or any example...
In earlier releases of the mfw for the nRF9160, we got 3 files with the image, one of them being firmware.update.image.hex. This is missing in the new updates. How do we update...
Hi, I have a PCA10000 nrf51 dongle, I use with wireshark and the nrf sniffer plugin. I followed all installation steps for the version 3 of the sniffer and the latest version...
Hey guys,
I'm working with a Laird BL652-DVK (nrF 52832 - chip), Nordic SDK v.14.2.0 and SES (Segger Embedded Studio v.4.30). My goal is to send datas from sensor (accelerometer...
hi
i use sdk12.3 (51822), i see only ble_app_hids_keyboard and ble_app_hids_mouse.
I want use mouse +kb device. I use ble_app_hids_mouse add kb function . then my android...
Dear All,
For a reason that I can't understand so far, I must erase the nRF52840 to be able to use UART1, TX RX on pins 0 1 (connector P14) to communicate with an external...
Hi,
Do you know which of the two version of ADP5360 the Thingy 91 uses?
is it
ADP5360ACBZ-1-R7 or
ADP5360ACBZ-2-R7
Both versions are available now at Analog's...
SDK: 15.3.0 Device: EYSHJNZWZ (nRF52832)
"nrfx_wdt_event_handler_t" can be set in "nrf_drv_wdt_init". After the "nrfx_wdt_event_handler_t" event occurs, the WDT is reset...
