Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
I am interested in optimising inputs for ADC measurement on an nRF52.
I have seen quite a bit about nRF51 but am unsure if this remains relevant for nRF52?
Hi!
I have an nRF52832 on a custom board. I managed to flash it through JLink and STLinkv2. But suddenly, I wasn't able to communicate to it anymore.
Openocd tells me...
Hi
The new signed DFU in the SDK12.1 comes along with a experimental buttonless DFU. There are a few bugfixes required to make it working, but the nRF Toolbox app didn...
Hi:
Recently, I want to use nRF52 to read or write some data from a flash chip(w25q128bv) by using spi, I've read Manufactures ID correctly, also, I have wrote a register...
Hello!
I need to interact with two J-Link debuggers, connected to the same PC at the same time. I would then read and write data to the devices connected to the debuggers...
Hi team,
iam using sdk 12.1.0 (ble_app_beacon) I want to advertise the battery percentage.Right now iam using the nrf dongle(it doesn't have cell coin battery) and flashing...
I am attempting to build some ptorotype code using SDK 12.2.0 and GCC and I just added calls to the app_schedukler library and to the saadc driver. I added the relevant source...
I always read 0 first time I call sd_ble_gatts_value_get(), the second time and forward I read correct value. Even if I call sd_ble_gatts_value_get() twice in a row the first...
Hello,
I generated a new project using the main.c of the example "ble_app_uart" from the SKD 12.2 for a nrf52832 and from there copying all necessary .h and .c-files into...
Hi DevZone
I am trying to DFU OTA a PCA10040 using BLE Secure DFU Bootloader from SDK12.2.0.
I can succesfully transfer the image i have made with nrfutil to my DK,...
Hi,
I'm working on integrating ANCS on our existing and futur products. I started to port the Nordic SDK example (12.x) and it seems to work fine on nRF52, which will be...
I am currently using SDK 12.1.0 and experiencing intermittent HardFault crashes in timer_list_remove() with the stack indicating the origin being a SWI0_IRQHandler call. ...
i have a setup with one NRF24L01+ as PTX and one NRF51822 as PRX
my problem is that the data sended ok and ack sended to NRF24L01+(i assume that by NRF_ESB_EVENT_TX_SUCCESS...
