Background - We are laying out a new board, upgrading to the nRF54, and wanted to use p2.02 and p2.03 as serial UART lines because p1.04 and p1.05 were planned to be used...
Hi there,
I have recently upgraded my software to latest ncs 3.2.0. I have noticed that my initialisation does complete but it ends up with fatal error that seems to be...
Dear Nordic,
I am debugging a custom hardware with a nRF7002 on-board, using wifi shell app. At this moment the shell does not work as expected, needs to locate where the...
I am attempting to install nRF Connect SDK along with VS Code on an offline machine for development. The main two issues I have are:
The NRF Connect for VS Code plugin...
Hi
I am using the nRF54L15 DK and build a thread continueing monitor the data rate in 1 Hz, if it is lower to 800kbps I want to change to 1M; while above 800kbps I want...
Hi all,
I’m Bruce — first-time poster but have been working with the nRF9160 on and off for a while now, mainly in outdoor, power-constrained telemetry and monitoring applications...
I have a simple GATT server application with two characteristics, RX and TX. In my prj.conf, I am trying to disable pairing as follows :
I can connect to the server from...
I'm using s120 v2.1, with SDK 9, on an nRF51 with 256K ROM and 16K RAM. With s120 I only have 6K of usable RAM for my application. I am running critically low on RAM, and...
I am using a nRF51 dongle as a BLE tranciever and using UART to communicate with an 8bit AVR. I used BLE_APP_UART peripheral example and mostly just changed the pins used...
Hi,
I am trying to update the battery level of my Battery Service but get keep getting an error. The error code is : 0x00003002. I cannot find any mention of what this...
I am trying to start programming in nrf51822 module with the waveshare kit. but the kit always shows the error as switch to boot-loader mode . how to solve this problem?
i am using nrf51822 wavshare kit with ulink2 debugger.
when ever i try to program the kit using keil the error pops like "overlapping of address in 00014000H".
then...
Hi,
I am using nrf51822 and SDK 8.0.0 , SD2.1.0 as an central and SD8.0.0 as peripheral. I am following ble_app_multilink_central and ble_app_multilink_peripheral example...
Hello,
We have a custom board using nrf51822.
In keil the board is detecting at 20khz clock for SW port in the debug window, we are able to program through keil.
...
This fork of the MBED CMSIS-DAP firmware seems to be the latest updated one. The title says, 'Interface firmware providing USB CMSIS-DAP for debugging, USB MSD for programming...
Hello,
I try to change a value by using sd_ble_gatts_value_set(...). If there is a connection, this works fine. But now I have to change the value also, if there is no...
Hi again.
I'm using nRF52 DK board in Ubuntu. I can flash the device with the blinky example (I haven't yet tried the softdevice tough), but I cannot really get any traces...
20160316_113235.jpg Hi guys,
i have 20 nodes and a central in my network, that are very close to each other except central device ( All of nodes are in a approximately...
Hi,
I'm wondering why are there scan parameters on creating connection? If I refer to SD130, create connection function , there is a note which tells us that if scan is...
I have 2 existing products, one using the nRF24LE1 and the other having a 2.4GHz ANT radio. Is there a way to have the 2 products communicate wirelessly? If it is possible...
Hi.
Quest to get the toolchain working under ubuntu continues.
I've done the eclipse and jlink config as explained in the nrf51 linux tutorial (with of course keeping...
