Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
I want to use ANT and BLE concurrently.
I found that there are no multiprotocol examples in SDK12 for NRF51422 (PCA10028). It only have example for NRF52832 (ble_ant_app_hrm...
Hi all,
i use softdevice and app timer.
I know that the softdevice use a RTC0 and app timer RTC1.
I would use a rtc to have a timestamp. but i see that after 512 second...
My function need a time window to get value from sensor,but the prcess always interrupted by SD.I know that the priority of SD is higher than app functions. So how can get...
Hello friends. How to write a number to and read from internal flash. My information about the microcontroller is very weak. I use STM32F103RET6 .
I test The following program...
Hello,
I'm starting to program a Nordic microcontroller, the nRF52. I was able to compile the various examples.
Now I would like to create my own project and use the...
The FDS requires data to be word-aligned and multiple of the word size. How do I ensure that my source/destination data structures are properly sized/aligned?
E.g. I want...
Hi, would like to know if anyone has some experience and advise how to get an external 51822 based board programmed and working via the nRF52DK. All the wiring works, I can...
pc cannot recognize nrf51 DK board.
what I have done.
erase all - not work (log.log attached)
power on with reset button. and copy J-Link OB-SAM3U128-V2-NordicSemi...
I have 5 nRF52832 development boards.....
I'm using Visual Studio 2015 and a Visual GDB plugin.
I have loaded and built the BLE Le example.
I start the debugging...
I'm using SDK 12.2. The FDS operates on word-sized data. How can I ensure that my data structures are word aligned and multiples of the word size? E.g. if I'm trying to write...
Hi everyone,
I am looking for reports and/or certifications that can help with our own device's certification process.
Would you know where we could find such reports...
Can I configure security parameters my own way?
I read some BLE profile but there are not explain about security configuration.
And I tested by using PCA10028, iPhone4s...
I am trying to setup an interrupt to fire whenever any of 6 GPIO pins change value using an nRF51822 with soft device. I found the example that uses GPIOTE to get an interrupt...
Hi. I'm using nRF51822AC, SDK12.2.0. S130 v2.0.1.
I just want to make DFU program. But I think it's a little bit confusing. So I want some explain.
Q1. What is the difference...
