I was working with IAR and SDK10.0 before. For some reason I have to transfer my project to Keil and SDK9.0. My program worked well for the old settings. While keeps got NRF_ERROR_SOC_NVIC_INTERRUPT_NOT_AVAILABLE...
Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
I have a problem through which unfortunately I'm not able to come across alone. I'm using nRF52832 with softdevice and UART central example from SDK14.2 (..\examples...
I have a client device that normally is able to call ble_db_discovery_start and get the callback just fine and is able to complete the db discovery process. However sometimes...
I try to use SPI with easy DMA, in page 279 in the datasheet says: " An SPI master transaction consists of a sequence started by the START task followed by a number of events...
I have an issue with waking up SPI communication after sleep.
Befor I go to sleep I'm disabling SPI communication:
NRF_SPI0->ENABLE = 0;
NRF_SPI1->ENABLE = 0;
...
Hi is there anyone who knows if you can change the time on how often the health server model send out, the health server model is from lightswitch demo
Hi,
I wanna use nrf51822 as master which has 2 slaves: sdcard (fatfs) and adc
I set SPI_INSTANCE 0
and they don't want to work together, I mean I'd like to write some...
A time T_PINR is specified in the datasheet, as shown in the snippet below.
Does this give me an indication of the pulse width for a pin reset? If so, how do I interpret...
Not really a question, just that I find the comment misleading. In the sdk_config.h example coming with the SDK there is this piece of code:
// <q> SAADC_CONFIG_LP_MODE...
Hello,
I am trying to establish communication between Win 10 PC and nRF52 Dev Kit using pc-ble-driver . I followed the instructions in:
https://github.com/NordicSemiconductor...
RN2903 is LoraWAN module using ASCII Command Interface over UART.
RN2903 is connected with nRF52-DK.
I'm connected uart line tx, rx gnd.(cross connect...)
UART communication...
Hi,
My desire is to connect a BC832 module (with nRF52832 on it) to a UART on a controller board and then send data from an iOS app (programmed in Swift) through the BLE...
Hello,
I need two signals with a phase shift to control my motor. For some reason, completely randomly, sometimes my GPIOTE event is not triggered and i get the inversion...
Hi All,
Based on nRF52832 SDK14.2 rtc example, I want to change it to retrigger RTC Compare0, let the LED1 also toggle every 3s, instead of keeping LED1 on. I tried to add...
Hi, guys, I have an IR receiver module with 3 pin (AX-1838HS) ?
How can I use it on my nrf52832 ? I have PCA10040 development board. I don't know how to connect them and...
