Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
Hello guys,
I wan`t to make an project that send trough serial port a new image to flash my nrf9160.
By the moment I managed to send and recieve data but only on uart0...
Hi,
Iam running the BLE uart and zigbee light multi protocol example. Using the latest thread and zigbee SDK v3.2.0. The example is quite good. That the door(zigbee+BLE...
Hello,
Where do I find the plating material information for the following part numbers? is it Matte Tin?
Nordic Semiconductor nRF51822-QFAB-T
Nordic Semiconductor...
I design a 4 layer pcb which include nrf52832. But i'm unsure what rf trace width should be on 4 layers pcb?
This trace 30mil width and 5mil clearance for 2 layers pcb as...
Hi,
I am using NRF52. i have custom board on that external flash and SD card is not available. i want to use msc class so that i can drag and drop file and read it in controller...
Suddenly my app, running on iOS 7, is reporting lots of spontaneous disconnects by the peripheral device, an nRF51822, indicating a timeout:
didDisconnectPeripheral: Peripheral...
Hi !
I added " Read Characteristic" in NUS.
How can I get different values every time I click "read again"? For example, read the value of a varying ADC from here. ...
I am investigating increasing throughput in our application. Upon investigation both with our software and the ble_app_att_mtu_throughput example code. I found that there...
Hello! I want to develop such a functional: nrf52840 receives a line from my application that it saves to memory, and then, when I click on the button, it returns this line...
Peripheral: nrf52832
Central: nrf52840
The communication speed after executing sd_ble_gap_conn_param_update is different in the following two cases.
case 1:
...
Hello
I am trying to do BLE communication using nRF52832. I wrote the exact same program on a module (BLENano2) with the same nRF52832 chip, but one was able to do BLE...
Hi.
- Is it the case that before every write to persistent storage via nrf_fstorage_write, the page written to has to be erased first (via nrf_fstorage_erase) since only...
I have used nrf51Dk with nrfPPK before some days now trying to flash nrf51DK but its not detecting any board I tried to recover but not recovering it I have already added...
Hello,
I am using nRF52840, SDK_16.0.0, S140 SoftDevice and Segger 4.16 for flashing the image.
1) For Secure Serial bootloader in below path, I want to change Tx...
