Hello:
The latest nRF54L15 Errata for Rev 2 shows that the previously reported "GPIOs can exhibit radiated emissions" is no longer present in the Rev 2 SoC.
Can you please...
Hi, this is a very broad issue that i am having, because i dont know the source of it. I am simply unable to use the bme68x IAQ library. i have downloaded the external bsec...
Greetings!
I am using Wireshark along with an nRF52840 dongle to monitor BLE traffic between a mobile app and connected peripheral and periodically I see some "L2CAP Fragment...
Hello, I am using the nRF54L15 board, and trying to connect to the Adafruit SHARP 400x240 monochrome LCD display .
I got the display driver alone to function just fine after...
Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Hello, i intsalled the software stack for use with latest release of nrf sniffer package.
By starting the capture process with wireshark 3.2 i have noticed an issue:
In...
I have a project where we have 2 nrf51 that need to be time synced with eachother.
The problem is they are placed on the body one on the back and one on the chest of a person...
SDK 16.0
nRF 52 DK
LIS3DH Axis sensor
I am trying to understand the sdk_config.h about the NRFX_TWIM_ENABLED config. Here the 'M' stands for Manager or Master? If I...
Hello,
I am using nRF52840, SDK_16.0.0, S140 SoftDevice and Segger 4.16 for flashing the image. I am using ‘ble_app_blinky’.
1) In Product specification, it says 2...
I'm developing a USB Keyboard Receiver. But I founed that there's no APIs and no descriptions about HOW TO SEND CONSUMER KEY and NORMAL KEY in USB HID mode.
I find a lot...
hello：
I want to communicate with my nrf25U1 USB dongle. So i add some code（refer to the examples\proprietary_rf\gzll\gzp_desktop_emulator）. When i add add these files(nrf_gzp...
Hi, Everyone
I am developing with SDK 15.3.0 and nRF52832
Compiling "examples \ secure_bootloader \ pca10040_uart_debug" and "examples \ secure_bootloader \ pca10040_uart...
I can't find anything on this error on Nordic support or Segger support sites. I've looked into the obj directory and only find one main.o file (of course!). Can't see anything...
Hi. We are using a BLE module based on Nordic nRF52832 in a new product we are developing.
The nRF52832 & softdevice has its own QDID - 115277.
However the module also...
I am trying to get a project working with a main.cpp file, some C++ modules, and the 16.0.0 SDK using the IAR compiler. However, using the nrfx/mdk startup files, it never...
Hi,
Iam running the BLE uart and Zigbee light multi protocol example. Using the latest thread and Zigbee SDK v3.2.0. The example is quite good. That the door(Zigbee+BLE...
Hello.
I would like to make simple GPIO bridge. That means transmitter with Digital input and receiver with digital output. When the state of DI changes, it's transferred...
Hi everyone,
I am using nRF52 DK with 52832 on it. My current SDK version is 15.2.0. I know that for IoT applications there is external hardware needed as router like RPi...
Hi,
I have a problem with a specific Zigbee certified device that I can't connect to my Nordic device.
When trying to connect to the device, I go to see the status:
...
Hi,
In need to debug my application using segger IDE when there is bootloader already present in nrf52832 chip .
The sdk we are using is SDK 15.3
Bootloader:- "secure_bootloader_ble_s132_pca10040...
