Hi,
I'm working on a project originally based on the light switch example of SDK 1.0.0 and then upgraded to Mesh_SDK 2.0.1 and nRF5_SDK_15.0.0
I use the code shown in...
I am looking for a freelance / contract developer to help us get nRF53840 working as a BLE controller under linux. ie: basic BT linux adapter. Integrated with BlueZ and similar...
Dear all,
I use FDS module to store some data in flash of nRF52832. I modified the example "ble_app_uart" based nRF5_SDK_15.2.0_9412b96 to test the fds functions feature...
Hello,
I am using nrf51422 with stm32L0. There is a uart connection between nrf51422 and stm32l0. I want to transfer data from stm32l0 to nrf51422 through usart and push...
hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
I want to make a programmer for nrf52832. Do you know where is the documentation of SWD is ?
Note: I found the similar question, but the links are not active
Hi
I am using Segger Embedded Studio and SDK_v15.3.0. I have a C++ code that I wish to run on the board. It has a lot of printfs. I want to see the output of the print statements...
Hi,
I'm new to Nordic Semi chips (nrf52840) and need to use TWI as a master to connect to two sensors. But I'm a bit confused about the different drivers: TWI and TWIM....
Hello to all,
I have a problem related to the client side Global Attribute: I have implemented an "On / Off Switch" that presents the cluster On / Off (0x0006), client side...
Hello,
When we analyzing the traffic of our application (many thanks to the team developing the sniffer), we have several questions about sending write confirmation.
for...
We do have a product in which we program a bootloader on the target. It is remotely based on the ble_app_buttonless_dfu example. The bootloader is not actually used in the...
Hi I am building a software watchdog to monitor nrf52 peripheral states to have higher confidence for 10+ years battery lifetime. The idea is to check every few seconds if...
I am working with the S140 softdevice v6.1.0. The message sequence charts located on the Nordic infocenter are great help. Question: are they available in a printable form...
Hi,
Is there any editable software available that I can use to create a custom interface between my PC and my nrF58210 module. I have been successfully using the Nordic...
How to program flash with the output HEX file and SoftDevice file using NRF52-DK.
When programming with the output HEX file the device does not work, I need also HEX - SoftDevice...
I'm trying to set up a project with SDK 16.0.0 using FreeRTOS with the softdevice. The device will be battery powered and therefore power management capabilities are required...
Hi all,
I am trying to generally gain a better understanding of the GPIOTE module and how it can benefit myself in the project I am working on.
I am essentially attempting...
Hello
Does the nRF5280 include Schmitt-trigger inputs on the GPIO pins?
If yes, what are the voltage threasholds for the rising- / falling edges?
(Can't find anything...
Hi,
How does disconnect work in S112?
In the ble_template project, I did not find anything in DISCONNECT event.
static void ble_evt_handler(ble_evt_t const * p_ble_evt...
I have a nrf52833 pca10100 which can connect to nRF Connect Desktop to program fine. EVBW833 should have the same chip DK but it is not being recognized. Is there a way I...
