Hi
I have two DKs, previously they work well, however, after I add the nRF21540 FEM on each DK, I always receive this in my central device:
Whether the amplifier cause...
Hi, I am currently trying to get through the NRF connect SDK fundamentals, I am on lesson 3 example 1, creating an application. The problem I am running into is that I cannot...
Background - We are laying out a new board, upgrading to the nRF54, and wanted to use p2.02 and p2.03 as serial UART lines because p1.04 and p1.05 were planned to be used...
Dear Nordic,
I am debugging a custom hardware with a nRF7002 on-board, using wifi shell app. At this moment the shell does not work as expected, needs to locate where the...
I am attempting to install nRF Connect SDK along with VS Code on an offline machine for development. The main two issues I have are:
The NRF Connect for VS Code plugin...
Hi
I am using the nRF54L15 DK and build a thread continueing monitor the data rate in 1 Hz, if it is lower to 800kbps I want to change to 1M; while above 800kbps I want...
Hi all,
I’m Bruce — first-time poster but have been working with the nRF9160 on and off for a while now, mainly in outdoor, power-constrained telemetry and monitoring applications...
Hi All,
I'm developing my product based on nrf51822.
I was using keil IDE for that.but i wanted to develop it in Segger instead keil ide.
is segger is supporting for...
Hello, I am working on an IoT project. For this project , I need to send some data using BLE. I developed a firmware for this application based on the sample ncs/zephyr/samples...
HI ,
In our project we are using multiple gpiote and app timer interrupt.
SDK we are using is 15.3
DOUBTS
If both gpiote and app timer interrupt trigger simultaneously...
Hi,
I'm using nRF mesh library v1.2.1 and integrating into my mobile application which I am developing, I implemented provision functionality without errors but sometimes...
I am bringing up a custom board based on the PCA10040.
As the first step, I simply copied (no changes) the file pca10040.h and named it as "my_custom.h". I then defined...
We have an nRF52 DK system running ble_app_uart_c example code and communicating with a peripheral device. We setup a second development system using another nRF52 DK system...
I have the nRF52840-DK with the adafruit PN532 RFID/NFC shield installed on top of it.
I run the TWI Scanner and receive a report that a device was found at address 0x24...
I am having a strange issue with my custom radio protocol. I have ported the code to the 52840 and SDK15 from the nrf51822 where it is running with no issues.
The issue...
Hello,
I have PCA10040 development board with nRF52832, Softdevice S132 v6.1.0 & SDK 15.1.0). I wanted to use the extended advertisement feature to advertise more than 255...
Hi,
After developing two application, one for emitting extended advertising and other one for scanning this kind of advertising on nRF52840 DK (Github repository here: MOTAM...
Hi,
I would like to ask two questions.
1)
I understand that the nrf52832 does not support the feature "Transmitter has a Stable Modulation Index".
But the component...
Hello, I am trying to build the asset tracker reference app for my newly acquired Thingy:91.
I went through the instructions to get the toolchain and SEGGER IDE up and...
Hello,
We are currently using a Raytac SoM that has nRF51822 SoC with Adafruit UART firmware. We are running into two different scenarios BLE connectivity issues where the...
While going though the Makefile of the FreeRTOS HRS example in SDK 16.0.0, I noticed this part:
By default, link time optimization (LTO) is not enabled.
If I enable...
