Why project config is not finding relative path of these files but absolute path works fine:
CONFIG_CHIP_FACTORY_DATA_USER_CERTS_DAC_CERT = "certs/Chip-DAC-Cert.der" ...
Hi!
I faced an issue with nRF Cloud Log. If I set CONFIG_LOG_TIMESTAMP_USE_REALTIME=y, I get wrong timestamps (2080 year..) in nRF Cloud Portal for all messages being...
Hi!
We use nRF Cloud Log backend in our project. And during my research I found that it actually doesn't filter (despite the filtering code is there) messages generated...
I am looking for a solution where I can set custom and configurable root Kconfig file via Cmake cache variable, which can be specified through the west build command.
Steps...
I'm working on an Android app that connects to a Nordic nRF52833 BLE peripheral (Zephyr 3.7.99 / NCS 2.9.0). I'm encountering a consistent issue where:
The app connects...
I have been testing the thingy91x and measuring power consumption trying to reduce it to the absolute minimum.
Using a test program that moslty sleeps ( using k_sleep()...
Hello,
I'm working on a project using the nRF52840 and Zephyr, and I'm experiencing an issue when trying to use device power management (PM) with a custom sensor driver...
Our system will awake from an external accelerometer interrupt, so I would need a code fragment which shuts down S110 soft device (and radio of course) and also all the nRF51822...
Hi,
I'm trying to test a new nrf51 board using the s130 softdevice and the ble_app_hrs_130 example. However, the program seems to hang in the ble_stack_init function (code...
I'm trying to implement DFU-OTA (Bluetooth transport) for our custom board and currently i'm facing problems in flashing the different elements (softdevice, bootloader, application...
I need to implement a PWM analyzer. I looked at the example in SDK 6 and it's fairly easy to follow. When I tried it, it doesn't look like GPIOTE handler gets called frequently...
I'm trying to backport the code form SDK 9.0 to SDK 7.2,
but i need to make sure that can be supported.
I found the "ATT-51", and there is a table about that,but the last...
ble_dtm.c has some bugs related to signed integer representation which prevent negative power (less than 0 dBm) from being requested in the vendor specific message.
...
Hi, all.
I'm using "SEGGER_RTT_printf" for debugging. Because have no uart port on my development board.
I want print double type variable like below.
double pi...
I am currently trying to communicate with a GPS module using the UART on an nRF51422 (using the Dynastream N548M5CB module). I am using SDK v9.0.0 and the FIFO version of...
Hi,
I want to send a continuous stream of data very quickly into the nRF51 through SPI and then dispatching it to a smartphone via BLE.
However I keep getting BLE no...
Hello
When i am in keil uvision 5.18 and use the pack installer all the examples using Softdevice S110 are gone in Keil. Is this a known issue and is there any way to solve...
I followed the instructions and comments in devzone.nordicsemi.com/.../ . I built a project around the ble_app_gls example (with a couple of minor changes such as using -DNRF_LOG_USES_RTT...
Hi, I would like to program nRF51822 flash over SWD interface. I have another micro LPC1100 series that has the flash image for RF51822 and connected to nRF51822 over SWDIO...
Hi,
It is written in the nf_drv_uart.h file for nrf_drv_uart_rx_abort() that
If Easy DMA is not used event will be
called from the function context. If
Easy DMA...
Dear All,
We work on the NRF52 CSP revB. We have a board with two external crystals (32MhZ and 32kHz).
When we use the example program with BLE and UART, it works great...
