I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
I am using single NRF24LU1P-F32Q32-T ic.i am using it only as a TAG transponder card .i wanted to know that can we program it to transmit only if there is no other controller...
hello everybody,
I measured the current consumption in two cases : in the advertising mode the current is around 4 ~ 5uA, & in the connected mode, the current is 160 uA...
Hi,
I am new to forum and to Ble. sorry about my week English.
I am working on a project where I am reading adc value every 1s and sending it over ble. So I have written...
Hi,
I'm using nRF dev kit with Softdevice 1.0.0.3.alpha. The device shows advertising state at LED1 as it should, however i can't detect "Nordic_UART" via nRF Master Control...
Is the advertising interval between two packets P1 and P2 defined as:
Interval = P2_start - P1_stop (time between packets)
or
Interval = P2_start - P1_start (time...
In a project I worked on using softdevice s110 v. 7.1.0, if the receiver hadn't enabled notifications, sd_ble_gatts_hvx would return an error, so I used the following construct...
Hi,
I want to advertise multiple UUIDs, one after another
Do I have to stop advertising, or is there a way, that I can update the struct in the background?
Currently...
I have two UART devices on a custom board with an nRF51822. I've just upgraded the SDK I use from 8.1.0 to 10.0.0 and one of the UART connections has stopped working, but...
Totally get the limitation of 3 PWM channels.
Wondering if I can dynamically re-assign which 3 pins are tied to the PWM outputs.
At boot time, I call this function:...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi All,
I have got reliable writes working on nordic side (nrf51822 eval board).
Tested them with master emulator dongle by using write long button on MCP on PC.
I...
Hi, I'm porting my project from SDK8.1 to SDK10 and got a problem in app_timer.c
Main chip :nRF51822 QFACA1
Crystal:32Mhz, no 32.768
Initial is fine.
APP_TIMER_INIT...
Hi, I realize that the compatability matrix states that SDKs 7 8 and 9 are built for rev3 of the nrf51822 and nrf51422. It has been mentioned however that they may still work...
The S130 SD supports up to 3 concurrent central connections. Once it has made the maximum number of connections can it still scan for non-connecting peripherals, e.g. to look...
