Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
My problems with Eclipse Luna continue. Going on holiday for a week I assumed the good fairies would sort it out, but no,,,
Anyhow, I'm sure it's some path error somewhere...
I'm trying to figure out something I'm seeing. I've modified the relay demo in the nRF52 SDK so that when I press button 2 on the board, it destroys any connections, erases...
Hello Everyone,
I have configured gpio pins for buzzer pin6 and pin 7 and am trying to clear those pins after buzzer making the beep sound but it is not getting cleared...
hello there i downloaded nRF51_SDK_10.0.0_dc26b5e.and run this example experimental_ble_app_blinky_s110_pca10028. here when i write 1 from master control panel LED turn on...
Hi,
I've asked a couple of questions around this before but that was before I thoroughly researched into what I was actually asking.
I would like to attempt to use the...
Hi,
I am currently working with the nrf8001-DK. I've connected the nRF8001/nRF24L01+ shield adapter to an Arduino UNO R3.
I've run the ble_uart_project_with_dfu_template...
This isn't really a question, but I'm not sure where to post something like this. The stock app_button_init takes a pointer to a non- const app_button_cfg_t . The library...
Hello,
i am working with nrf_pwm library which is there in git. Also, on my device, with PTR51822, S110 7v is running. I am having tri color led on the device, by using...
Helm alert.7z Hello!
I have tried to make a additional custom service with a characteristic to contain data from a sensor value. I want the server to only send the value...
I have a problem with some current consumption I cannot explain.
I first thought it had something to do with floating pins or something, but that does not seem to be the...
According to the nrf52 product specifications, the PWM peripheral consumes 200 uA running at 16MHz. But a TIMER in combination with PPI an GPIOTE consumes 30.1uA max. Why...
Hi Nordic,
Which version of nrf toolbox for IOS can upgrade the zip file containing application hex, bootloader hex and softdevice hex together? I found the DFU function...
Hi Nodic enginner;
Now i am using 51822 in my product. I find that there is a 2.5mA current in my board that is no firmware. The question i want to ask is that how much...
