Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I have been slogging my way through documentation and examples and have managed to create a beacon application using the development kit and Segger IDE. That said I am fumbling...
We are working on the GPS sample code found in the ncs\nrf\samples\nrf9160\gps folder of the nRF Connect SDK 1.1.0 tag in the repository.
The modem firmware version we...
If a record in a file with MESH_CONFIG_STRATEGY_ON_POWER_DOWN have been changed the NRF_MESH_EVT_CONFIG_STABLE is never emitted until mesh_config_power_down() is called. ...
Hi
I am working with nrf52832 development kit. I am trying to write device information service from central device to peripheral device.
I am successfully able to write...
Hello Devzone,
I've been using nRF52810, SoftDevice 112 (5.1.1), for a Mic recording application. What I'm trying to do is sample PDM MEMS mic data through PDM interface...
Dear Team,
I have nRF52 DK and nRF52840 DK, Can we program nRF9160 using nRF52 DK?
Please let me know the process and detailed wiring to program nRF9160.
Ashiq Moha...
Hi,
Good Day!
Statement of Problem: We use Li-Ion Battery in our application and would like to monitor a few variables such as Battery Voltage, Battery temperature & Discharge...
Hello, I'm trying to set up SPI communication with a sensor from my nrf5284_pca10056 running zephyr.
This is my prj.conf file:
This is my .overlay file:
And this...
I'm looking at the GPIO functions in http://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/zephyr/reference/peripherals/gpio.html , and looking at the function prototype...
Hi
I'm have and NRF52840 with a MPU9250 connected via TWI. The connection to the MPU9250 is successful, I can find its address on the bus (0x68).
I've implemented a very...
I am trying to add to an existing project gpiote
I have copied the code from the example project and tried to add all the files and changes to my sdk_config.h to match the...
Hello all,
I'm trying to develop a basic bike computer, compatible with ANT+. For that, I'm using nRF52 DK. My main objective is to be able to connect to any commercial...
Hello,
I have nRF52840 with code that is based on SDK16.
I am not using Softdevice in my project - just MBR , Bootloader and Application.
I was able to upgrade my code...
Hi all,
We are successfully using the nRF52840 chip in one of our projects except for the DFU functionality. We tried following these tutorials without success:
devzone...
