Hi,
We're at a point in our project where we're working through some regulatory testing for ETSI/FCC certifications with our BLE dongle board (nRF52840 + nRF21540 FEM...
Hi,
I'm using zephyr RTOS.
I'd like to put the cpu System ON Sleep Mode to conserve power.
Then, I'd like to restart the CPU with an interrupt or event from the comparator...
Dear Staff,
we have some Ublox C2909 TAG based on your nRF52833 chip.We need to program them for an RTLS project.
In particular we need to:
customize the FW here ...
Hello,
I managed to run the examples for nrf54l15 channel_sounding_ras_initiator.c and reflector on my custom hardware boards. I changed the overlay files to use my own...
Hi all,
I want to fully understand the concept of Bluetooth protocol using nrf52811. Any advice will be helpful for me!
First, as I understand softdevice is Bluetooth...
As shown in the figure, MCUboot has a boot_go_hook function. I'd like to define this function in my own project and compile it into MCUboot. Since I'm using single slot DFU...
Hi ,
I am trying to interface sg90 toy servo with NRF52840 , I am using nrf library but dont know how to drive it from 0 degree to 90 degree to 180 degree . May I know the...
Hi
I m using NRF52832 for beacon application.In my application, the device should be in the system off mode .After holding button for 5 secs, the system will back to idle...
Hi
I'm using SDK version15.2 and SD on a custom board based on nRF52840.
The board has two serial ports, and I want to use both independently. Using the Serial Port Library...
Hi Nordic Team,
My requirement is-
Advertise -> Connect to 1 device -> Send packet -> Disconnect -> Delay(1min) -> Advertise -> Connect to 2 device...
I am using Timer...
I am using nrfMeshProvision cocoapod to create a Mesh Network using a iOS Mobile application. In first step of identifying the device, i am able to call bearer.open() and...
Hi,
I've used the nRF connect 'Getting Started' software and tutorial to setup a development environment, however i am having problems with the "Set up a project in SEGGER...
Hi Nordic Team,
Please share a logic to filter with address for connection over BLE. Please help as soon as possible.
Thanks & Regards,
Aswati Vijaykumar
Hi
I am currently developing a demo application and started with the ble_app_template project from the ble_peripheral_folder (s140 softdevice, sdk 16.0). I copied it to...
I am using a module called Core51822 which includes NRF51822, with the NRF51822 Evaluation kit and the ST Link to program it from Arduino IDE.
I want basically to program...
can someone suggest me some tutorials how to do programming in nrf52840 from scratch.
i have tried some examples like blink an led just like opening the file and running...
Hallo devzone,
i have a real time task, where i have a trigger, different calculations and then the corresponding action.
Now i need to calculate the time from the trigger...
Hello,
As I am new to the world of bluetooth and its stack I have a question which I cannot find the answer for on the internet.
I've read a ton of posts on the devzone...
Hi Nordic Team,
Requirement-
Connect->Send 1 packet->Disconnect->Connect...
I am Sending a data packet to central using Timer handler and trying to disconnect using...
Good day.
I am trying to add flash storage functionality to a project based on the ANT asynchronous transmitter example and the ANT back ground channel example of the SDK...
I am using the nRF51822 QFAAH0 Chip and running it on 90 mAh battery. Currently I am using the AMS1117 3.3v LDO voltage regulator. It is running as iBeacon for 7 hours. I...
