Hi,
I'm struggling to get a mouse wheel to work in advanced (High Res) mode.
What I learned so far is that I should create a "Resolution Multiplier" Feature report....
i set up an coap/iot environment and but i was getting error while compiling code for adc i followed steps from this post devzone.nordicsemi.com/.../ here is the problem
Hi all,
I've developed a broadband vibration energy harvester that is able to pick up uW of energy from just a couple Hz all the way to 150Hz. I'm currently looking for...
We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
hello:
our hardware engineer had designed PCB,it can't reach more than 100m..howerer the nrf52840 DK can reach 300 or more meter.
so is there any people can support some...
When using nrfutil to generate a DFU settings page (with backup page) of settings version 2, the .hex-file generated by nrfutil is not word-aligned, i.e. the number of bytes...
I noticed that as of SDK v16 a required component to use the Soft Device is nrf_section_iter which is located in the directory "\libraries\experimental_section_vars". Is this...
Hello,
The product specification for the nRF52832 only shows 3.0V performance. What is the performance in parameters such as Tx power, Rx sensitivity, maximum MCU clocking...
Hi,
I'm currently developing firmware in the Arduino environment using a dev board (Adafruit Feather nRF52840). Once I complete development, how do I transition the firmware...
Hi, I am developing the application in nRF52832 with SDK_16 in SES.
I have a problem with DFU
I need to run the application and DFU has to be activate only if the mobile...
Hello everyone
I'm using NRF MESH4.0, I have add simple_on_off model to experimental_dimming example,and it works .
My question is : MESH PROFILE V1.0 have mentioned bound...
Hello, i am trying to adapt DFU in the Light switch Proxy server example, however in midle the process of receive the DFU packets i got this error: Abort event. packet loss...
Has anyone (tried to) simultaneously use the same QSPI Flash memory directly from an nRF52840 program and as a USB block device?
We have both functions running in the same...
Hi
I am working with nRF52832 DK, using Segger IDE. I want to read data(a file) from a computer and process the data on DK. Is there any way of doing it? Also, is it possible...
Hi Nordic Team:
Can you help me to support BIS or CIS example .btt file。This file was captured by Ellisys tool。So ,I can refer to file ，and understand 5.2 Core Spec about...
Referencing the recommended 52840 PCB layout for the WLCSP package, we noticed two thru-hole vias in the middle of the ground area (in the center of the package). Do these...
Hello,
I am trying to implement ble DFU on our custom nRF52832 board. Up until now we have had no issues with our application running as SoftDevice+Application but some...
I'm attempting to send a time sync message in a mesh packet. When I construct the packet during it's timeslot (for timing determinism) the system faults during encryption...
