We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Hello,
I'm working with the Nrf52832 Dev Kit and the ble_uart_example. After flashing with the hex file and powering the Dev Kit, the on-board-LED starts to blink. Now I...
Hi Nordic team,
I am currently developing a concurrent wireless application with BLE and a proprietary protocol using the timeslot API.
My setup:
nRf52840 DK
SDK...
Hello, guys!
We are working with SDK 15.0.0 and nRF52840 SoCs.
There is a need to transfer a few MBytes of data from the PC to nRF52840 and then on external flash memory...
Hi
this is the code I'm trying with my buzzer,
I want it to generate sound but with different frequencies.
".base_clock = NRF_PWM_CLK_1MHz," I can only as low as 125kHz...
Hey guys,
I'm working with a Laird BL652-DVK (nrF 52832 - chip), Nordic SDK v.14.2.0 and SES (Segger Embedded Studio v.4.30). I am trying to combine the examples ble_app_uart...
Hello.
I am trying to run the throughput example for the Connect SDK, using a 52840 DK and a 52833 DK.
https://github.com/NordicPlayground/fw-nrfconnect-nrf/tree/master...
With sdk16 cli, each command displays help message when used with -h option. It would be nice to have a help command which can display all active commands and their help ...
Hi,
I would like to use raytac MDBT50Q-U without an 32 mhz external crystal.
Periphal examples like "blinky" work but ble does not? nrf_sdh_enable_request fails with invalid...
Hello,
I am using SDK SDK_15.3.0_59ac345 with soft device in application that controls a GPS IC from UART (AT command), also the application is running in background beacon...
I refer the following the link . https://devzone.nordicsemi.com/f/nordic-q-a/33606/updating-advertising-data-manuf-spec-data-in-sdk15
I understand the adv data update. I...
Dear Sirs,
I would like to use in my program computed heart rate as a parameter.
Could you please give example how can I get to this value? I just found in page_0 such...
Hello,
I'm trying using \examples\ble_peripheral\ble_app_uart on PCA10040
I'm programmed s132_nrf52_6.1.1_softdevice, using nRF5_SDK_15.3.0_59ac345 with pca10040_s112_nrf52832_xxaa...
Hi,
Why is it that when NRFFW[0] = 0xFFFFFFFF SVC calls are passed on to the softdevice but when NRFFW[0] = 0x19000 they are passed on to the SVC handler of the application...
Do you have template for nRF52832/PCA10040 with s113 ?
If no, what have to change in my template for nRF52832 that works with s112:
c_preprocessor_definitions
S112...
My problem is a little bit weird: I don't get a HardFault, although I'd want so.
SDK-12.3.0 (d7731ad), FreeRTOS (from the SDK) and SoftDevice S130 (2.0.1) also from the...
