I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I want send ble bond connection request from raspberry pi to nrf51882.
Can you please let me know which ble libraries I need to send central ble bond request to nrf51882...
Hi,
My goal is to capture on gpio burst infrared proprietary "messages" composed of multiple "bits".
The Length of each bit is around 100 to 200us.
Initially I planned...
(I understand my question is similar to devzone.nordicsemi.com/.../ , but I would like some additional clarification not provided in that post.)
Hello, I've been developing...
On a BLE_GAP_EVT_CONNECTED, I'll send some data to an attached microcontroller via UART. The code will expect a response of that data, all while being inside that BLE_GAP_EVT_CONNECTED...
My application involves the Nrf52 using softdevice and a slave only SPI ADC running at approximately 26khz. The ADC has a pin interrupt to indicate data ready. There seems...
Building nrf_delay.c (or anything else including nrf_delay.h ) with NRF52 defined produces:
arm-none-eabi-gcc -I C:\Nordic\nRF5_SDK_11.0.0-2.alpha\components\device -D_DEBUG...
Hi, someone know whi when i press disconnect on iphone the nrf51 restart from the mail?!
Why if i disconnect android device the chip does not restart as the iphone?! is normal...
I'm trying to build BLE driver 0.5.0 for 64bits.
I've downloaded:
MinGW 4.8.2 64bits
boost 1.56 and compiled it using address-model=64
CMake 3.4.1
Python...
Hello Nordic community:
I've read about Serialization in the nRF51 SDK doc and would like to prototype an example with it.
I saw a notice of it being removed post 7...
Hi,
Is it possible to get a more detailed description of the GPIO block than what is available in the reference manual? Specifically i'm interested in how the disconnect...
Hello Everyone,
I want to run a couple of test on the nRF51422 radio. However, how do I go about checking the firmware on these devices without the use of a motherboard...
Our device fetches fused quaternion from MPU and transmits via NRF 51822.we are using 3.7v li-ion battery.we are using Non-volatile memory.
Currently we are facing these...
I am trying to run BLE central peripheral dual role on nrf52 pca10040 with nrf_uart as service. Also, I have redbearlab BLE nano as peripheral (nrf51822 based).
I am getting...
Hi, I would like to ask that, whenever I put my function in main.c, the borad become undiscoverable.
I'm using nRF51 with ble_app_uart_s110_pca10028, and below are my function...
