I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hi,
I am porting a SDK 2.6.0 project to SDK 2.9.0. It gets built without errors but when I try to run it after flashing I get the following.
I am not sure where to start...
Hey All! I've been following the nRF Connect SDK Intermediate course from DevAcademy. In exercise 2 of lesson 9, bootloaders, you get to learn how to use KMU (Hardware Key...
I've developed a custom Matter application based on the Matter samples in the Nordic Connect SDK, targeting the nrf52840. I developed the first version using the nrf52840dk...
Dear Nordic Semiconductor Support Team,
I hope this message finds you well.
I am currently evaluating the nRF52840 for use in an industrial/automotive application and...
Hi Nordic team,
I’m currently testing UART communication on nRF54L15 with NCS 2.8.0 , and I’ve encountered an issue I’d like to ask about.
When using UART20 configured...
Hi
Does the nrf-sw-pwm driver work on the nrf54l15. I am porting code form the nrf52840.
My output does not toggel, 0% and 100% does work but noting else.
I tried running the " Bluetooth: nRF Distance Measurement with Bluetooth LE discovery " case in the SDK, here is its link： Bluetooth: nRF Distance Measurement with Bluetooth...
Hello,
I'm trying to connect a BMI270 sensor over I2C using Port2 on the nRF54L15 , with the nRF54L15 DK , and I'm working with the nRF Connect SDK v2.9.0 , based on a Zephyr...
Hello,
I have the nRF7002 DK, which includes the nRF5340 (App + BLE cores) on-board.
The hardware requirements do not list this DK as usable for the course, which seems...
Hello,
I am currently designing with the nrf52840 and trying to implement the 32 MHz crystal required for bluetooth radio operation. The calculations for the load capacitance...
Hello,
I am attempting to build the Matter template using only the nRF54L15’s internal memory. While the build occasionally succeeds, it more often fails, and I am unsure...
The nRF52832 devices have been produced in hundreds of units. Currently, it has been found that individual central devices are problematic – connecting to peripherals often...
I have enabled all the dependencies asked as below
CONFIG_IMG_MANAGER =y
CONFIG_STREAM_FLASH =y
CONFIG_BOOTLOADER_MCUBOOT =y
CONFIG_DFU_TARGET_MCUBOOT =y
Still...
I work for ChannelSounding on nRF54L15.(NCS3.0.1)
I measured the distance using two nRF54L15-DKs. The actual distance was 3m. The average measurement result is shown below...
