I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi. I'm trying to use GCC instead of Keil.
I have followed "nRF51 Development with GCC and Eclipse" written by Nordic and "nrf51-pure-gcc-setup"( github.com/.../nrf51-pure...
I want to write PCA20006 nRF51822 Beacon Firmware to PCA10004 on nRF6330.
I understand need to modify GPIO.
PCA20006 firmware consist of 3 firmware, SoftDevice, application...
Hello.
I use nRF51822-EK.
I test ibeacon example source now, but i can't config my minor id.
Now my board minor id is 252(0xfc), I CAN'T CHANGE MINOR ID!!!!
How to T_T...
I'm trying to use the ADC and internal reference to measure battery voltage on the nrf51422, while S210 is enabled.
From the example nrf51-ble-app-temp-master, I found...
Hello,
I'm trying to use the nRF51822 evaluation board like a HID keyboard, so I'm fallowing a tutorial and I installed :
Keil mdk474
nRFgo Studio 1.17
nRF...
We are preparing BQB test for our BTLE product now.
Could you please help confirm if you have the test command to make 51822 into the test mode and can be auto-testing by...
Hi, I'm developing a HID-device using nrf51822, s110 ver 6.0.0 and SDK ver 5.2.
I would like to hide the device from unknown centrals once it's paired. I'm advertising...
I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
I'm using ble_uart_app & master control panel v3.5 for debugging uart communication. when uart is sending data to host(master control panel side), suddenly, master control...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Hello,
i use the bond manager together with a own module to store data in memory. On user interaction i want to delete the whole memory. I proceed as follows:
Disconnect...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
I am using the eval board, sdk v5.2.0, s110 v5.0 and a galaxy nexus with the UART Nordic app. I have not been able to receive any data on the android end. After
void nus_data_handler...
