Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hello!
So I can connect, disconnect and write to my applications characteristics via a PyQt5 GUI I threw together. On the python backend, I use Bleak to
search for devices...
Hi, I am developing using nrf52832 and st7735s.
Successfully displayed the lcd screen using the code in \examples\peripheral\gfx
However, when screen clear, text_8print...
Dear friend I checked the data sheet of 52820 and I didn't see any LPCOMP peripherals. Check the data sheet of 52832, there are LPCOMP peripherals. Comparing COMP and LPCOMP...
Hi,
I am working on internal flash nRF52832 merged with twi sensor, my sensor function will return a string . How to assign the string to the my_data.p_data . i am getting...
Hello Nordic
Using the old SDK, i was able to do FOTA wiht 10kb/s.
After doing all kinds of tweaks, I am only able to obtain 5kb/s with the new connect SDK.
Can i...
Hi,
I am using the nrf54l15 on a custom board in our current project and want to use it with DFU over BLE FOTA as well as TF-M.
I can compile the project just fine before...
Hello,
I am currently using the nrfutil application to convert modem trace logs to pcaps through an automated process. I am seeing intermittent failures with the following...
I'm running the peripheral_ancs_client using the 2.9.0 SDK on a nRF5340-DK. On an iPhone running iOS18, the device is not visible under Settings->Bluetooth when the nRF5340...
Dear Nordic-Support,
I have registered handlers for the two voltage level thresholds with the nrf modem library using modem_battery_low_level_handler_set and modem_battery_pofwarn_handler_set...
Hello,
I am developping an application based on PAwR (Periodic Advertsing with response) in coded PHY (S8) extended advertising on SDK 2.7.0.
costum chip nrf52840 (on...
Hello, I am currently developing a testing software to verify whether all the pins of my module have been properly connected. I configured pin 1.03 as a high level in the...
Hi everyone, I have a custom board in nrf52833. Currently, the gpios on nrf52833 are gone, except for the NReset pin (P0.18). Can I configure the NReset GPIO as a GPIO I/O...
Hi Nordic team,
I tried to view logs from my custom nRF54L15-based MCU using J-Link RTT Viewer, but it's (printk) not working. The same prj.conf configuration was previously...
Hi,
Our products have been mass-produced and now need BQB certification, but the certification fails.
IC：nRF54L15 ncs2.9.1
base project: ncs_v2.9.1\v2.9.1\nrf\samples...
Hi,
I would like to know the difference between the nRF52840-QIAA & nRF52840-QIAA -R7.
What is the significance of R7 here. Not able to find it in any conclusion ...
Dear Nordic Semiconductor Team, I hope this message finds you well. I am currently developing a project called Nuntius Core, which involves controlling bait boats (carp fishing...
Custom PCB with nrf5340/nrf7002. Currently was using NCS2.9.0, with WPA2-PSK connection to the wifi.
While trying to enable use of WPA2-Enterprise, I updated to NCS3.0.0...
I have a custom board using a nRF52840.
A part of the configuration is a Analog Devices MAX98357AEWL+T Class D amplifier which is driven by i2s0.
When the board is idle...
Hi Sir,
As we know the nPM2100 support AA/AAA batteries, LiMnO2 coin cells (e.g., CR2032), Alkaline coin cells (e.g., LR44) .
But could nPM2100 support CR123A 1S2P?
...
