Hey Team,
I'm trying to flash the audio application on our custom PCB, this PCB follows the interfaces of the nrf5340 audio dk. Previously on lower SDK versions (2.7-2.9...
Hi Nordic team,
This is a follow-up to my previous question here:
Can nRF52833 perform PAwR while also syncing to another PAwR device?
We are now extending our design...
Hi,
I'm trying to build nmea parser, so I have a functionc hecking all nmea sentences and trying to get double value, but I always go bad double value. For example here...
Hi,
With several nrf52840 based prototypes, I had serious problems. I could see them die after flasing them a few times. And this was not just one dying, it was all of them...
Is a common ground required when measuring current in current meter way?
Can externally supplied voltage exceed 5V? Will this cause inaccurate test results?
I'm working with nRF5340 and nRF Connect SDK 2.9.0, using sysbuild and Partition Manager for my project. I want to enable Zephyr's coredump feature and store dumps in internal...
How can I display the nrf serial terminal logs files on VS Code while keeping the same colors and text highlights for dbg , inf , wrn , etc., just like when viewing live logs...
I'm using NCS SDK v3.0.2 and trying to build the Matter Thermostat example for the target: ` nrf54L15DK/nrf54L15/cpuapp/ns ` However, the build fails with the following errors...
Hi,
I am testing the Bluetooth function on my custom board with nRF5340 CLAA chip. I have tested the clock, I2S and SPI on this chip previously and they all worked perfectly...
I can flash the chip. I can run the debugger. I can go to the connected devices, select the device, go to the little "plug" symbol on the RTT, and select it. That brings up...
I am trying to set up a w25q128 using SPI with a nrf5340 on a custom board and had a few questions. I have used DevAcademy as a reference as I do eventually want to set up...
I have been using the nRF54L15- PDK(0.8.1) to test various examples and projects, and everything has been working fine so far. I recently switched to the nRF54L15- DK(0.9...
Hi, we are planning to use npm1300 for charging a battery, but we will have a limitation on the power supply (VBUS in npm1300 naming convention): the capability of making...
Hi, I'm currently trying to add an Actinius Icarus IoT board as LTE device at nRF cloud.
I already know my board IMEI (I got it by flashing the AT client sample and then...
I have a custom board with nRF52840. It draws power over USB and the data lines are connected as well
USB is defined as follows in the dts
cdc_acm_uart0: cdc_acm_uart0...
Hi everyone,
I'm using the nRF Connect SDK 3.0.2 and the nRF Connect Toolchain 3.0.1 with the matter ‘light_bulb’ example. I just want to do the following: 1) Get exactly...
Hi,
I am Currently running BLE Mesh with nrF5340DKs, I refer all nodes as Cores but 1 as Master, Master receives and Stores data as well send data to PC Serially for further...
Hello, I have been observing some interesting behavior concerning packets sent from server during eDRX idle period. When the period is set to 20.48s or 40.96s, any packet...
Hi,
nRF5340 and SDK v3.0.0 I'm using.
Currently my nRF5340 based BLE device can be bonded with smartphone via passkey, after bond is done, the device stops advertising...
We are building project with this config parameters: But we get this error messages while compile: If we use CONFIG_LOG =n for mcuboot, then project compiles normally. Also...
Hi,
Is it possible to make the MQTT connected device receive the Shadow config updates and AT Commands immediately? Based from our testing, the device only receives the...
