here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
The errata for the nRF52 indicates higher consumption in managing timers and GPIOTE. Does the BSP for SDK11 follow recommended practice to deal with these errata can I ask...
I am using nRF51822 with S130 stack.
Some of my flash write works fine, some return NRF_ERROR_INVALID_ADDR,
I could not figure out exact cause, all my addres is word-aligned...
Hello,
I know this issue has been discussed several times on the Dev Zone, but in every post, i found the same answer and this answer does not help me.
As I read, intalling...
Hello.
I try to build small network: 1 central device (CD), several relay devices (RD), several broadcast devices (ED). CD and RD have to receive commands all the time...
I am using adv_report_parse to try and return the device names the scanner picks up. However it returns some bizarre charters after the name....
it should read P Device...
hello,
Please forgive me if I am asking a stupid question.
I was editing S130 demo app and I included pstorage.c file to the project. while compiling it is showing error...
I have compiled my mbed program and hex file has been downloaded but I am unable to drag and drop my hex file to mbed USB drive. It is saying Not Ejected properly. I tried...
I am following app note nAN-29 "nRF51 Development with GCC and Eclipse Application Note v1.1". In the section "Flash download" there is mention of an executable called nrfjprog...
Hi
I use the PORT EVENT to produce multiple interrupts.But I have a question by these:
NRF_GPIO->PIN_CNF[BUTTON1] =
(GPIO_PIN_CNF_SENSE_Low << GPIO_PIN_CNF_SENSE_Pos...
Hi,
have some of you expierence with profiling on a nrf51422? I think what would be nessesary, is at least one high priority timer, to sample the program counter, some kind...
Hi,
I’ trying to save some user configuration data on the NRF51822 Flash using pstorage module.
Below is the code that I wrote, the code runs on the board with no error...
I have two boards based on nRF51822 parts:
Nordic dev kit PCA10005 Rev 2.2.0 2014.14, chip marked N51822-QFAAG0-1351AG
Custom board with Fujitsu MBH7BLZ02-109004...
I'm getting an error which says the identifier ble_temperature_t is undefined, and it is showing as an error in the keil (unkown type name). However when I click on the variable...
Hi everybody,
I just received the nRF51822 EK and as I was starting to set it up I ran into this. It took me a while to figure it out but when trying lo load the blinky...