hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
Hi !
I know that there is a way of OTA updating the nrf8200 application. But i'm not sure if this process requires aditional hardware like it happens when using the BLE113...
Hi All,
I am able to successfully connect to nrf51822 EK using BlueZ 5.12 and can read many of the characteristics except for the temperature value.
I understand that...
Hello
I have a project about voice communication.
Trying to do bidirectional voice communication, is there any possible to work on nrf51822
It means whatever via Bluetooth...
Hi,
I have version 2.0.0 of Evaluation Kit. I was waiting for the new SDK and SD 6.0.0 but I have seen the warning about hardware versions. I have to finish a SoftDevice...
I'm a noob in this alley! it is my first time working with Nordic products. In the past I used Energy Micro and ST Micro.
I downloaded Keil 4.x from ARM website. Then I...
Hello,
I am developing a project using nRF51922 and S310, and the project is built using SDK4.2.2 with the modifications mentioned in a document called "nRF51922 - ble...
We are looking to understand the internal working of the nRF51822 firmware (MEFW_nRF51822_0.9.0_firmware.hex). If someone can share the original code or the basic block diagram...
Hi folks,
I want to match my IFA PCB antenna to the nRF8001. As Harald recommended a couple times, I am going to measure the antenna of the final PCB with a Vector Network...
Hi All,
I use the 51822 DK to do the current measurement and do as the DK user guide 5.1.8 current measurement.
I just use the __WFI() to make the 51822 get into idle...
Hi!
I must match NRF24L01 to 40+j48 ohm antenna. This is not my design, so
no possibility to change. I have PCB antenna, that was measured to be 40+j48 inside
enclosure...
I have some non-volatile storage routines that I have written before, but the new SDK V5.0.0 has this pstorage module that is supposed to replace it, right? How do I migrate...
I use 51822 nrf6130 "device_firmware_updates" example to update AP. When I build "dfu_dual_bank",the update will success. But when I use "dfu_single_bank",the update will...
Hi,
Do the nrf_temp functions, nrf_temp_init() and nrf_temp_read() only work for the nrf6310 board? Are there equivalent functions for the EK?
Thanks,
Mike
I have been trying to connect a nrf8001 device to a Android 4.3 device and it is discovered ok but fails when it tries to do a service discovery. After some deep digging I...
