Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
I'd like to use the GATT/GAP driver from an ARM based Linux system. Is there any possibility of getting a library compiled for ARM or (cough) the source code to build it myself...
It is possible to run easily a SoftDevice stack (e.g. S110) on nRF51422 using an accurate 16MHz external clock reference for HFCLK instead of an external 16 MHz crystal oscillator...
I want to change data bytes in the advertisement packet. In ACI_DEVICE_STANDBY I put: lib_aci_open_adv_pipe(1);
In ACI_EVT_CMD_RSP: I get feedback that command 1B (I assume...
first,PCA10005 can't load sofeware hex that after s110 7.0.0 hex(include 7.0.0),and gostudio note that the given hex file can not open successfully.
second,the PCA10005...
I am finding it difficult to figure out what is the minimum toolchain requirement to get started developing using the nRF24LE / U.
Is Kiel the only compiler ? Can SDCC...
Hi,
I have nRF51822 DK with (s110_nrf51822_7.0.0, nRF51 SDK_v6.1.0.0) and when i try to run the project in IAR 7.20.2 i receive an error.
2 ) My icf file...
Hi!
I have bought the nrf51822 EV KIT and it came with 5 extra nrf51822 modules but them without a board. I have researched a little and I found that I need the Segger...
Hi,
We're using an off the shelf module with a trace antenna that can't be modified.
Measured the module once assembled, and due to surrounding plastic materials, the...
Just finished upgrading to the latest SDK Version -- and trying to build some of the examples -- but consistently getting compilation errors when building any of the nRF51822...
When working with BLE, one sees a lot of different names for roles, which is confusing. What is actually the difference between them all, master, slave, central, peripheral...
Hello to everyone,
I'm developing a new project with a nrf8002 and a Smartphone with Android 4.4.2. Both devices connect to each other fine, and I can bond them with no...
Hi,
I made a peripheral firmware based on "s110\experimental\ble_app_uart" example, but I don't know how to write a central module FW so that these two can pair to each...
The reset handler as shown in the C:\Keil_v5\ARM\Device\Nordic\nrf51822\Source\templates\arm\arm_startup_nrf51.s will call SystemInit as defined in the C:\Keil_v5\ARM\Device...
Hi
im unable to connect nrf51822 EK with nrfgo studio
how can i solve this issue
m using all latest version softwares
and wen i click ok it shows as below
...
Hello, i know its an often discussed topic but i already read lots of threads about it and didnt find the answer.
I have a simple program that enables the softdevice s110...
Hi,
We are using an nRF8001 with bonding.
We tested the use case were a bond has been established with an iOS app. Then the connection was terminated by closing the...
Hi
am using a thermistor of 10 k with a known resistor of 10 k ,and am giving the voltage divided input to ANI2 (p0.02).The suppply voltage for thermistor is external of...
Hi,
We designed an nrf51822 BLE application using the mbed kit and on-line tools.
Our target pcb has a 1.8V onboard supply. To minimise consumption i want to disable the...
I have an android client that functions as a central and have an app on my MAC (peripheral) that this central connects to and sends data.
At this point, I need to wait...
