Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
Hello together,
I am searching for the source code of the MasterControl Panel for Android.
Is there a reason, that the code is not available, because the source code of...
Hello,
I'd like to know, if there is any difference between nRF51822 EK and DK, except device number. Two devices from EK will be enough for me.
www.nordicsemi.com/....
Hi,
We are interested in integrating BT MP3 player in our product and Im wondering if we can use Nordic SoC to stream audio via bluetooth to the Headset? So create an A2DP...
Hello, I am trying to develop a low power application by using nrf51822 EK board.
In " Reference manual v2.0, 11.1.3 System ON mode ",
it says there is a mechanisms can...
I am using app_gpiote_user_register() and ads_interrupt_enable() to define a ping change interrupt. When the code runs, I can see on my logic analyzer that the GPIO pin assigned...
I have a nrf51822 project with S110 (v6.0.0) softdevice. I am using latest sdk (v5.1.0). I compile the project successfully with gcc and it does run too. But I struggle with...
I'm trying to reconcile two things I read about the softdevice. The GAP roles that are supported include broadcaster and peripheral. Also, there is support for a GATT client...
Hello
I am trying to build the nAN-36 application.
The main.c file include at least two files that I do not find:
#include "ble_eval_board_pins.h"
#include "ble_stack_handler...
We're trying to implement initial programming of the chip using SWD. We can connect to the chip and successfully enter debug mode but from that point on (as per section 11...
Hi,
I'm gong to design a pcb for nRF81522 (for both packages: QFN 48 pin and 64 pin WLCSP). I coudn't find the footprint in any documents. I appreciate if anyone can send...
Hi all,
Trying to read out the nRF8001 serial number using the nRF8001 SDK 1.7 and I cant seem to work out where I should be making the call to lib_aci_get_address?
After...
I'm a wireless novice, but have electronics experience.
I'm looking to add bluetooth low energy communication from a battery powered MIDI controller to a Macbook Air (or...
Ole,
I am trying to update the serial number value in an already initialized standard Device ID profile.
[i]dis_init.serial_num_str.length = (uint16_t)strlen(newserial);...
Hi,
We are trying to reuse the RF frontend design provided in reference design of PCA10000-nRF51822 Development Dongle 2_0. But because we have different board thickness...
