Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
Hi,
where could i find detailed current consumption and timings (wake-up, rx, tx, power down) in connected mode for RF51822, in order to compute average current value for...
My device :
nRF6310 Rev 1.4(nRF6700)
nRF2722 Rev 2.2
I will use those devices to test RF communication between nRF2722 and nRF51822. Software environment is...
Hello,
I am playing with the s110 ble_app_proximity example.
As I do not want to store info in flash, I do not want to use the bond manager, that stores data in flash...
I'm currently using a combination of the GNU ARM Eclipse plugin and the unofficial pure-gcc Makefiles to build my nRF51822 code. The build works fine with the pure-gcc Makefiles...
Hello everyone,
I want to create a real-time wireless sensor network. There are 8 sensors in the net. I use two nRF24LE1 as receivers to recieve the datas stimultaneously...
Any idea what the max SPI slave clock frequency is on the nRF51822? The product specification (page 46, v2.0) says the max SCK frequency is 2MHz, but I was wondering if any...
Hello together,
I am searching for the source code of the MasterControl Panel for Android.
Is there a reason, that the code is not available, because the source code of...
Hello,
I'd like to know, if there is any difference between nRF51822 EK and DK, except device number. Two devices from EK will be enough for me.
www.nordicsemi.com/....
Hi,
We are interested in integrating BT MP3 player in our product and Im wondering if we can use Nordic SoC to stream audio via bluetooth to the Headset? So create an A2DP...
Hello, I am trying to develop a low power application by using nrf51822 EK board.
In " Reference manual v2.0, 11.1.3 System ON mode ",
it says there is a mechanisms can...
I am using app_gpiote_user_register() and ads_interrupt_enable() to define a ping change interrupt. When the code runs, I can see on my logic analyzer that the GPIO pin assigned...
I have a nrf51822 project with S110 (v6.0.0) softdevice. I am using latest sdk (v5.1.0). I compile the project successfully with gcc and it does run too. But I struggle with...
I'm trying to reconcile two things I read about the softdevice. The GAP roles that are supported include broadcaster and peripheral. Also, there is support for a GATT client...
Hello
I am trying to build the nAN-36 application.
The main.c file include at least two files that I do not find:
#include "ble_eval_board_pins.h"
#include "ble_stack_handler...
We're trying to implement initial programming of the chip using SWD. We can connect to the chip and successfully enter debug mode but from that point on (as per section 11...
