I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I am attempting to measure battery voltage through the ADC, but am getting inaccurate results. In my setup, I have a 4.2 V battery divided down to the bandgap range using...
HI all:
I am using the nrf24le1.And i confuse about the recive and transmission address in rf transceiver.
What do we use the address to do usually.It will be wonderful...
Copy nrf51.cdb to "C:\Keil\UV4"
Copy nrf51xxx.flm to "C:\Keil\ARM\Flash"
Set the keil project-device to nRF51822(data base : Nordic nRF Series Devices)
This is...
Hi
Is there a documentation of the nRF51822 sniffer interface? e.g. communication structure, command format, captured messages structure etc?
Thanks
Yaron
I'm trying to set up a network where 1 - 4 BLE devices wirelessly talk to a computer. I'm using an arduino connected to the BLE shield.
The computer is a Winows 7 laptop...
Hi,
I'm creating a project on nRF51822 chip and I have a problem with disconnection. In my program I want to disconnect with master after some time e.g. 30 seconds. I'm using...
I'm unable to write my application code to the flash of an NRF51922 (QFAACAA). NRF Studio will let me flash the hex file but it fails verification. If I try programming in...
I have a question, can nRF51822 operate in regular Bluetooth mode like a Bluetooth 2.1 device?
If answer is no then, is there any product from Nordic that operate as Classic...
Hi developers,
I've finally got the nrf51822 working and advertising a good signal to the dongle. :)
After doing all the steps in the NAN-36 pdf-file I hoped that pressing...
Hi all,
I'm using Timer2 while having the SD enabled, and I'm having some problems. I don't seem to be able to reliably set the periodicity of the timer. No matter what I...
I've spent quite a while getting Eclipse on Mac OSX working. I started with the original makefile but have come up with, finally, a working native Eclipse build which does...
Hi all,
I have an external dongle (Bluegiga) that is scanning for BLE devices.
My problem is this: all the BLE devices in my room are showed correctly except my nRF51822...
Is there a link where I can find all sources of applications for NRF51822 corresponding at iOS App "nRF Utility" (with explanations of use of both systems)?
Thanks for...
I 'm developing using a nrf51822
and use 256kb rom 16kb ram.
I met ram overflow frequently.
so,I want to calculate the ram size at the map file.
could you explain how...
Hi,
We are using the nRF905 device in an application where it needs to switch between auto-retransmitting and sending single packets, due to it communicating with several...
