Hi, this is a very broad issue that i am having, because i dont know the source of it. I am simply unable to use the bme68x IAQ library. i have downloaded the external bsec...
Greetings!
I am using Wireshark along with an nRF52840 dongle to monitor BLE traffic between a mobile app and connected peripheral and periodically I see some "L2CAP Fragment...
Hello, I am using the nRF54L15 board, and trying to connect to the Adafruit SHARP 400x240 monochrome LCD display .
I got the display driver alone to function just fine after...
Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Dear Nordic, I'm using TIMER21 for our library, but I encounter problems with CC channels 6 and 7: their compare events never fire. The problem I configure the timer to generate...
Hi. I am trying to add DFU service to sourse code with existing service. When I try to run service without device manager + DFU or run device manager + DFU without my service...
Hello!
I am trying to build a connectable Eddystone beacon with a Blend Micro board which uses nRF8001 . I used the BLEPeripheral library ( github.com/.../arduino-BLEPeripheral...
Should I call app_sched_execute at least once before the first app_timer_start ? I have a strange bug and I realized that calling it before is a fix but I don't see this in...
Maybe this is a newbie question but, I read that using TEMP is a restricted resource for the SD but I could not find any driver or example to use it correctly.
Can someone...
I am trying to determine the suitable set-up to determine when my system's battery source (lipo battery) is too depleted.
I am running my nrf52 at 3 volts and the Lipo Battery...
Hi. I try to fusion 's130_nrf51_1.0.0_softdevice' and 'flash write'. I checked flash write. but when i implement flash write with s130 softdevice, it is not working. If i...
I have the nRF52 dev kit, and I hooked up pin 13 to SDA and pin 18 to SCL on an I2C device. There are no external pullups on the SDA or SCL lines.
However, the TWIM module...
I tested some features of the new nRF Connect application version 1.0 on PC. The application has a lot of interesting features useful to develop and debug embedded software...
Hello Everyone!
I want to make a project that will recognize some tone in the air, up to 5KHZ, and will send nrf8002 a message as a result.
I though to use the nrf52 proccess...
I am using SDK_11 s130 ble_app_gls on nRF51-dk.
An Android phone running nRF-Connect app was able to pair and bond with nRF51-dk. First time doing pairing and bonding works...
Okay, noob alert. I am designing a product that requires a simple iBeacon (redundant?).
I have this hardware on my bench:
nRF51822 Bluetooth Smart Beacon Kit and downloaded...
Hi, I am trying to write a small android app to send direct advertisement to particular device.
i am using 0001 for direct advertisment. But when i advertise the data, message...
Hi all,
In my project i want to transmit and receive one character by using 8051 controller. One is act as full transmitter and another one act as full receiver. In my...
