Hi
I have two DKs, previously they work well, however, after I add the nRF21540 FEM on each DK, I always receive this in my central device:
Whether the amplifier cause...
Hi, I am currently trying to get through the NRF connect SDK fundamentals, I am on lesson 3 example 1, creating an application. The problem I am running into is that I cannot...
Background - We are laying out a new board, upgrading to the nRF54, and wanted to use p2.02 and p2.03 as serial UART lines because p1.04 and p1.05 were planned to be used...
Hello,
I face a problem which I can't understand really and where I need support.
It is strange...
In our electronics we use the nRF52840 which is enclosed in a module...
Hi there,
I have recently upgraded my software to latest ncs 3.2.0. I have noticed that my initialisation does complete but it ends up with fatal error that seems to be...
Dear Nordic,
I am debugging a custom hardware with a nRF7002 on-board, using wifi shell app. At this moment the shell does not work as expected, needs to locate where the...
I am attempting to install nRF Connect SDK along with VS Code on an offline machine for development. The main two issues I have are:
The NRF Connect for VS Code plugin...
I need a reference design of nRF51822 for minimum 1 meter range . The circuit will run from CR2032 battery for at least 24 hours and will take some readings from ADC input...
i am unable to sniff the packets between two devices once the connection is established between two devices..i am using nRF sniffer 1.0 ...
i am able to see only the advertisement...
Hi,
How can I control the PDU error code when reading an attribute.
E.g. Attribbute not found 0x0A. For more info see 3.4.1 Error Handling Bluetooth spec 4.1 Volume 3...
Hi,
I have created a custom PCB that more or less follows the Nordic SmartBeacon design: Beacon_V2.pdf
Instead of BAL-NRF01D3 I used the BALF-NRF01D3 as this is supposed...
I have use random number generator in S110, the source code just like:
uint8_t num_rand_bytes_available;
err_code = sd_rand_application_bytes_available_get(&num_rand_bytes_available...
what does it mean the VTG led turn red ? but it has no bad effect to my project. In addition, I find a strange phenomenon. I use three 1.5v battery to power my board. The...
I ran the ble_aci_Tranport_layer_Verification.ino sketch from the Nordic BLE library and I get no output to the serial monitor after "nRF8001 Reset Done" is displayed. I think...
Hi nordics!
First of all, thanks for answering my questions before.
Now, I want to generate a clock(48 pulses) with 200us width.
However, sometimes the width of...
Hi ,
I have a application program which uses s110 and UART service .
The issue is the program is not working when I enable the Micro Lib in keil.
On observing the map file...
Hello,
I want to use flash for logging sensor data and sending via BLE.
I found several APIs for store data to flash.
pstorage (Persistent Storage Access Routines...
Hi all,
I would like to know how can I program and debug the nRF51822 development boards?
I've seen some boards have a built-in programmer and others haven't.
How can...
In the DFU code provided by nordic is explicitly states that.
"Soft reset from application must not reinitialize the SoftDevice."
In my application I do not have a button...
Hello,
I have made simple modifications to the multilink central and peripheral examples, adding an additional button and notification characteristic. Things have been...
We're designing a board with the nrf51822 QFA part. Due to design constraints, the chip will have to be about 15mm from where the antenna port will be. The routing to the...
