Hi,
Is it possible in BLE channel sounding in ncs 3.0.1 to get some information about the quality of the distance measurement for each method? We have three ways to get...
Hi,
my name is Nick De Leenheer, and i am finishing my thesis on indoor localisation with CHANNEL SOUNDING. i currently got these outputs in my venv using SERIAL: so i...
Hi,
I´m working on a Zigbee-based environment sensor. You can find all related files here: https://github.com/Kampi/BeeLight
Now I have the following scenario: the whole...
Does the nrf54l15 have a register to specify the boot area? Similar to the NRF_UICR->NRFFW of nrf52833.Or does the nrf54l15 have to boot from address 0x00000000?
Hello,
I've been going through the BLE fundamentals course and things are going well. I'm using the nRF5340DK board and SDK version 3.0.2
I've gotten to lesson 3, exercise...
Hi,
I am working on the channel sounding feature on the 54l15 and I want to perform it sequentially between 3 reflectors and one initiator. I realized that after I make...
Hi,
We're at a point in our project where we're working through some regulatory testing for ETSI/FCC certifications with our BLE dongle board (nRF52840 + nRF21540 FEM...
Hi. I got TCA6424A IC which communicates through i2c. I tried to use that with nordic but it doesnt respond. I used simple twi scanner application which should print address...
Dear nordic employee
My 52832’s GPIO control the external 32mhz crystal‘s power，
when the 52832 work in the sleepmode ,I cut the 32mhz crystal'power
then when I want...
Hi I have a problem with TWI (the slave part), that is, we can only receive on nrf52840 8 bit, there is someone who knows how to do so you can receive 16 bit, we have taken...
Is there possible to get timer period shorter than 12us with nRF51 and SDK 14? "timer" example with PCA10040 works correct, but with PCA10028 not. When set timer period lower...
When I go to build any of the nRF SDK BLE examples, I get linker errors that app_error_handler was not found. I now copy-and-paste a boilerplate version of that into the code...
Hello,
I'm currently trying to OTA update the firmware of my nRF52832 DK, I use the SDK 12.3.0.
I loaded the BLE Secure DFU Bootloader in the DK, it's advertising as...
Hello, i use nRF5_SDK_12.3.0_d7731ad. I took this tutorial https://devzone.nordicsemi.com/b/blog/posts/getting-started-with-nordics-secure-dfu-bootloader and according to...
Hi, Guys,
I am using nrf52832 for our product. Recently I updated stack and sdk from s132v2/sdk12.1 to s132v4/sdk13. However, I see a new characteristic under Generic Acess...
Hello,
I'm trying to run the example ble_app_uart using nRF52840PDK and iOS 11.
The device appears as Nordic_UART but when I connect, nothing shows up. The following screen...
Hi! Compiler errors are popping up when working on nrf_drv_rtc.c while log is enabled for this nRF module. I see that the problem is any log statement that contains EVT_TO_STR...
Good afternoon,
I have been doing some tests with the nRF SDK for Mesh v1.0.0, and have a question regarding it.
I'm using a fw based of the Light Switch example, to...
By using the DFU to transfer an updated version of the application, The nRF Connect tool pop-up tip:"upgrade succesfully". But the version of application mostly is still older...
Hi all,
I have been looking for the DFU library in objective-C, without any dependency manager such as cocoapods or Carthage (we cannot use them in our solution), but...
I found the thingy hardware files and I was wondering if one can buy the flexprint antenna from you or if you can connect us to your manufacturer.
We are planning to use...
