Hi,
my name is Nick De Leenheer, and i am finishing my thesis on indoor localisation with CHANNEL SOUNDING. i currently got these outputs in my venv using SERIAL: so i...
Hi,
I´m working on a Zigbee-based environment sensor. You can find all related files here: https://github.com/Kampi/BeeLight
Now I have the following scenario: the whole...
Does the nrf54l15 have a register to specify the boot area? Similar to the NRF_UICR->NRFFW of nrf52833.Or does the nrf54l15 have to boot from address 0x00000000?
Hello,
I've been going through the BLE fundamentals course and things are going well. I'm using the nRF5340DK board and SDK version 3.0.2
I've gotten to lesson 3, exercise...
Hi,
I am working on the channel sounding feature on the 54l15 and I want to perform it sequentially between 3 reflectors and one initiator. I realized that after I make...
Hi,
We're at a point in our project where we're working through some regulatory testing for ETSI/FCC certifications with our BLE dongle board (nRF52840 + nRF21540 FEM...
Hi,
I'm using zephyr RTOS.
I'd like to put the cpu System ON Sleep Mode to conserve power.
Then, I'd like to restart the CPU with an interrupt or event from the comparator...
I've noticed that if I have data queued to go out over the uart (using app_uart_fifo) if I do an fds_record_update the UART TX is effected. You can see what's happening in...
I have put my code developed on a nRF52 dk on a custom board that is based on a ISP1507 CPU. We are having higher current consumption than expected, I use the exact same code...
Hi There,
In company we are working with nRF8001 (currently C revision) and we want to send some custom data in an advertising packet. However, when C revision is selected...
From the S132 5.1.0 specification, I expect that its RAM usage should be only 0x1228 bytes plus ATTR_TAB_SIZE. However, when I compile two of the example projects using IAR...
I am working on a project in Nordic SDK 8.1 that requires using a timer. I am confused where I need to define the timer though (using APP_TIMER_DEF). If I put it right after...
I am working with the SDK 12, nrf52832 low_power_pwm example. I am concerned about the power consumption I am measuring.
I am trying to produce a 1khz PWM for an LED (the...
Howdy,
I am having difficulties writing to NVRAM (reading appears to be fine and is reporting 0xFF's everwhere). I am using a rather old SDK and SoftDevice 110 (version...
How much is the nRF52840 USB DP/DM pins impedance in transmit mode?
There is no info in datasheet .
On the PDK board there are 39 ohm resistors connected in series with...
The engineering B errata mentions PAN 186, that the current consumption in System ON Idle is increased if High-Voltage mode is used. Is there any information available how...
Hi everyone, I'm having troubles with a project using softdevice, and I think it could be a memory problem, I just wanted to confirm that the addresses are correct and there...
Why was this removed? The SD 3.0 docs show only random static and public as options and I get bad address for the others which is consistent with the docs. We were using random...
Hello
Nordic Team.
I controling nrf spi.
testing for example nrfSDK14.0.0\example\peripheral\spi\pca10040\blank\arm5_no_packs\spi_pca10040
/**
* Copyright (c...
Hello everyone, I want to run project ble_uart on NRF52832 in Keil.
At the beginning of the main.c I add
#define BOARD_NRF6310
But get error
C:\Keil_v5\ARM\PACK\NordicSemiconductor...
