I'm currently working through DevAcademy Lesson 5, Exercise 1 using the nRF9151 DK , following the CoAP client example. I’ve encountered an issue when attempting to POST data...
Hi all,
I'm trying to characterize the UDP throughput of a Thread network consisting of nRF5340 DK devices. I saw that Espressif made a test report and they seemed to use...
I’m using a custom PCB based on the Minew ME54BS01 module (nRF54L15 SoC) for both ends of our proof‑of‑concept: one node as a GATT‑based Channel‑Sounding reflector (leveraging...
Dear DevZone support,
I'm currently evaluating nPM1300 for Lithium Polymer battery management and charging and would like to ask a question.
I understand that I can...
Hi Nordic：
We are currently testing Zigbee on the nRF54L15 platform using the Zigbee R23-add-on-V1.0.0 SDK. It has been observed that when a low-power node disconnects from...
Hello, I am using ISP1907 which has NRF52833. I get the IQ data and configuration from serial as: DF_BEGIN ['IQ', 0, 0, 11, -9, -213] ['IQ', 1, 8, 11, -209, 23] ['IQ', 2,...
I have 2x Power Profiler Kit II up and running using the Power Profiler app - started twice and with separate PPK2 instances selected, as described in another support post...
I have a application where I need to time acurately the time between two enternal pin signals. I have this working using the
k_timer which & read & restart within the...
HI， In the Zephyr config, these【NET_IPV6_NBR_CACHE & NET_IPV6_ND】 are recommended to be enabled by default. Why does the Bulb project turn these off, and what impact will...
Hi I am currently trying to modify the Zephyr BLE Controller stack and getting exceptions. It seems the "J-Trace PRO Cortex-M" can help me with knowing how I get there. Buying...
Hi,
I have a board with a real time clock IC which is kept alive during power downs. I want the Nordic nrf52840 to read the time from the real time clock and then use this...
I don't have found CONFIG_OPENTHREAD_FTD feature in the bulb project prj.conf or prj_release.conf file, but I have found that it is enabled in the final .config file within...
Dear Nordic team,
I am currently working with the Thingy:91X (nRF9151) and nRF Connect SDK v2.9.0 , and I am attempting to run the official ECDSA sample from your documentation...
We are currently using an nRF53 in our plant sensor project, where we need to be able to enter sleep mode and be woken up via RTC and GPIO interrupt. Since the nRF53 does...
Hello.
I keep trying to control my GoPro camera via BLE. At first I tried to do it using the old sdk, but it didn't work ( devzone.nordicsemi.com/.../gopro-control-over...
Hello All
We are trying to integrate ST7305 driver with NRF connecct SDK and are unable to get the driver to work using the extrnal module method mentioned in the NCS Intermediate...
My device tree overlay GPIO section looks like this:
Note that I repurposing a GPIO that was used for an LED in the board's device tree file. Also note that node numbers...
Hello,
I am using the nfc_system_off example code to evaluate the characteristics of power off mode.
Current measurement is done by following the instruction shown in...
Hello
I created the out of tree sample sensor application with SDK 2.6.2 and it built just fine However it builds only when it is inside the sdk that was pulled when I selected...
Hey everyone. I am having an issue reading the WHO_AM_I register from the stm lsm6dsv16x. I am using the spi1 configuration as shown in the academy classes. I have very short...
