Hello!
I think there is a problem in NCS v3.3.0. nRF54L target, sysbuild build with MCUboot and TF-M, partition layout coming from devicetree (SB_CONFIG_PARTITION_MANAGER...
Hi, I'm developing a keyboard-pcb with NRF52840. I'm doing this as a hobby and are not that experienced with integrated circuits. Anyway, I designed and produced a pcb, but...
Hello,
in cases where the LTE signal strength is extremely low, we observed that the LwM2M /4/0/2 RSRP rolls over from -128 to 127. We found that the nRF Connect SDK uses...
As part of the Bluetooth LE course we need to setup and install the nRF BLE sniffer for wireshark. I have followed the explained steps in the course to set up wireshark to...
The at command documentation says that ENVEVAL is only available in system mode 2 (CFUN=2). Is there a reason why the command can't be run in any other mode? For example if...
Hi
The TWI driver has a twi_clear_bus() function but the TWIM does not.
I'm getting an I2C error, and need to do I2C soft reset. I'm doing this manually at moment but...
I recently completed a field-upgrade path from an nRF5 SDK 17.1 application (with the legacy Secure DFU bootloader) to a fresh NCS-based firmware stack, while preserving user...
Hi Nordic support:
Our project uses the nRF9151 and QM13545 MIPI RF SWITCH. We have a question about AT%XMIPIRFFECTRL command's frequency: If the frequency switching point...
Hello,
I encountered a very strange problem. This problem originated from my development of RGB color lights using the NRF52840. Due to the limitations of RGB color lights...
If anyone has successfully stored and retrieved settings on the nRF52840 dongle using any method, please share your approach.
I'm trying to store and retrieve settings...
We are testing SPI communication with the nrf5340 Board as the mater and the nrf52840 board as the slave.
The FW applied to nrf5340 is a FW whose normal operation was confirmed...
I have a problem understanding notifications/subscriptions in the BLE context.
I have two devices, Central (nRF5340) and Peripheral (nRF52832). My peripheral provides a...
This not a question. It is for your information (FYI). I've seen many questions about flashing the nRF53 using CMSIS-DAP. Anyone interested see attached instructions.
The...
Using an approach similar to what's in the ble_app_att_mtu_throughput example, my goal is to transfer data as fast as possible. (I.e. call sd_ble_gatts_hvx() on the same characteristic...
I'm building the nrf/samples/openthread/cli sample with the nrf54l15dk/nrf54l15/cpuapp/ns board. The only change I'm making is enabling CONFIG_DEBUG_THREAD_INFO.
The app...
Hello,
I am using an LE audio code "nrf5340_audio" code from nRF SDK v2.8.0 to play a beep tone. I want to play a tone from a temporary memory, so I have created a logic...
I'm following the dev academy lessons and I'm having a bit of an issue where VS Code intellisense isn't picking up on the include paths from zephyr (e.g. #include <zephyr...
Hi, while working with the nRF9160DK i get this Error a lot of times, I can't say "Yes" or something else and have to wait until the progress bar fills completely. Even if...
Hello
Our 52840-based device has a functionality of playing one of 10 pre-recorded phrases via I2S interface. We'd like to be able to update the wording or load a different...
When integrating DTM into my main app, I have to comment out the macro CONFIG_BT=y to ensure the DTM test can run properly after the build. Are there alternative ways to include...
Hi
I am working on nRF54L15-DK (PCA10156 0.9.2 2024.49) with chip N54L15 QFAAB0 2444AA
I am using Nordic SDK 3.0.2 and Zephyr 4.0.99
My task is to have the top 2K of...
