Hello,
I am trying to use LTE connectivity on a custom board with a nRF9160 SICA B1, but i am facing issues with the modem.
With both my own app firmware and the sample...
I have searched all responses here and whatever sources I can find, but not have any success. The main problem is that existing materials appear incompatible with the 54L...
I'm pulling my hair out here. Why would syntax errors completely break the toolchain?
Every now and then ill have a syntax error which causes the build to fail, the entire...
Hi, I have test the throughput using two nRF54L15 DKs and make them close to each other.
My result is:
1. My first question would be: the best througput for 2M phy is...
Hi,
We're working on a project using the nRF5340, where we interface an external NAND flash (4096 blocks) to store high-volume sensor data. We are planning to maintain an...
Hi,
We are currently evaluating the NRF9151 for asset tracking using the AT firmware on the NRF9151 evk and an external MCU for the application firmware, emulating the final...
Hello,
We’re Bachelor’s students developing a project to estimate the angle of arrival (AoA) using a BLE antenna array on the nRF52833. Our implementation builds on Zephyr...
Hello again,
I am messing around with connectionless BLE AOA CTE transmission using NCS 2.4. My setup includes the Siliconlabs BRD4191A which is a 4x4 BLE AOA/AOD dual polarized...
Hello,
We are developing a Bluetooth application that uses the Environmental Service to transmit various sensor data. Everything works correctly, but we have noticed an...
When building `nrf/tests/modules/mcuboot/direct_xip` with nRF SDK v2.9.0 for nRF54L15DK the build errors with the following ouput: Is there a fix in the pipeline for this...
Hello
I am doing a bluetooth dongle and I added MCUBOOT with CDC ACM to be able to update my app.
I find that the update takes a lot : 5+ min to update a 200kB application...
I need to send different types of advertisements in my application using NCS 2.9.0 on a nRF52833 and I noticed that I have to increase CONFIG_BT_CTLR_SDC_PERIPHERAL_COUNT...
Thingy:91X V1.0.0 (multiple devices)
NCS 2.6.2, nrf53_connectivity_bridge_v2.0.1
Using the logging of the nRF9151 via the nrf53_connectivity_bridge_v2.0.1 shows on longer...
Hi, We have a network of air quality nodes based on the nrf9160 using Vodacom in South Africa. One morning all the nodes went offline and we discovered that they no longer...
Hi, I am having trouble with the connection of my mesh nodes and my Smartphone over the nRF Mesh App. After flashing my boards ( nRF - 52833, 52840, and 7002), most of the...
HI all,
I'm trying to run the USB next stack-based loopback class with Linux testusb. and only very few of them been passed and everything else been timed out.
I confirmed...
Hello,
We have nRF52832 in production on a custom board. Recently, we created a new functionality with the aim to handle flash more efficiently, and to avoid the case where...
Hi All,
Hardware Details:
nRF-SDK: 2.8
Microcontroller: nRF52840
Setup:
We have an OpenThread (OT) mesh network consisting of approximately 15 devices. All devices...
We are trying to incorporate nRF9160 to our project. In which we need both GNSS and LTE features. The solution is a tracking device so we need the GPS functionality. We have...
I am looking to figure out my current consumption with an NRF52832 chip. I have the NRF chip running at 3V using UART, SAADC, BLE and SPI. The chip is constantly reading some...
Hello, I have been trying to install nRF Connect SDK v2.9.0 for 2 days. I am currently using Linux Mint 22 Cinnamon and git version 2.43.0. When I try to install it via toolchain...
