Hello Nordic Team,
For my application, I am using two nRF54L15 chips with one configured as a master and the other a slave. For the remainder of this post, I will be discussing...
Using VSCode with nRF Connect extension on Ubuntu Linux 22/04 with nRF SDK 3.0.1 and nRF Toolchain 3.0.1 installed I can create a build configuration for Zephyr's hello_world...
Hello DevZone team, I recently received a new nPM1300 Eval Kit (PCA10152, 1.3.0, 2025.19) and connected it the first time following the documentation ( docs.nordicsemi.com...
Hi everyone, I'm trying to set up a bootloader chain using sysbuild (NSIB → MCUboot → APP) so that MCUboot can act as an upgradable bootloader. I'm working with the nRF54L15...
hello Nordic
i am working with nre52840 and nrf52832, with ncs v2.8.0
i am using ble SMP service for transferring data with a central device and for DFU.
currently i...
I have noticed that Matter V1.4.1 has been supported from NCS V 3.0.0( https://docs.nordicsemi.com/bundle/ncs-latest/page/nrf/protocols/matter/index.html ), but I have not...
We are currently working through Exercise 5 – FOTA over Bluetooth Low Energy using the nRF5340 DK and encountering an issue where the mobile application (nRF Connect for Mobile...
Hi！
I'm working on direction finding. I'm using a nrf52833dk as a beacon, a nrf52833dk and a Direction Finding Antenna Board (PCA2005) as a locator for a bluetooth direction...
Hi All,
I recently received a few dev kit boards that I intended to use for a test fixture we are building. I tried to use it in our test fixture which had been working...
Hello, thingy53 qwicc connect shows 3.2V when pwrd on, yet there is 0v from thingy91x when turned on. Is there some other step needed to get 3.2V? thank-you,
Hello there,
Working on bringing up the FOTA feature on the 54L15. I began with the LBS example. I was using the Nordic "Device Manage" to push the FOTA build.
The state...
I've been using the following SPI2S pins and they've been working:
CLK -> P0.16 MOSI -> P0.17 MISO -> P0.19 CS -> P0.18
I want to use SPI1 instead but when I replace...
I have a two fold question, to build a prototype, I would like to know how to get
tflite micro in zephyr build for nRF9151 DK?
Non-Terrestrial Networks (NTN) on above...
I have been using the nRF Connect for Desktop with the Programmer application for several years to attach our end device to the Dev Kit to program our device with no issues...
Hi
Can the device(nrf52832) be used as a BLE Mesh Provisioner and Light Switch Client(such as Generic OnOff Client) at the same time?
I want to develop a device (nrf52832...
Thanks in advanced. Based on nRF5_SDK_17.0.2, I can use i2c with icm42670p normally. Due to power consideration, I need to r/w this imu with spi either to decide which is...
Hi,
I'm developing with nRF Connect SDK v2.9.0 in VS Code. I followed the exercise l1_e1 from the intermediate course. When I debug with breakpoints and the first breakpoint...
Hello there,
I reported this issue in another thread under a different symptom. With more and more testing, it shows it is somehow related to both Android and the 54L15...
Hello.
I need to read IMU data from LIS2DH12 of nrf 52833 which is in DWM3001CDK. But nothing I do initializes sensor... i always receive
<err> lis2dh: Failed to read...
Hello!
I am learning to obtain data by SPI protocol from ICM20948 sensor using nRF54l15. I tried to write my code based on sample given on devacademy nRF Connect SDK Intermediate...
We are developing with the nRF9131EK. But there is no documentation of this board.
https://docs.nordicsemi.com/category/nrf-91-series
Can You add the information like...
Before developing our custom board, we connected our MCU to the DK via pins 26, 27 and after disabling VCOM0 via the DK configurator, we were able to communicate using AT...
