Hi,
We have deployed some devices now, and we see quite some modem faults popping up.
Could you try to give all info on what you know about these faults we have from...
Environment
SoC: nRF54LM20 (DK; silicon reports nRF54LM20B ENGB — also reproduces built for the LM20A target)
nRF Connect SDK: v3.3.0-rc2, west v1.5.0
Bluetooth: SoftDevice...
Hello
We are using nRF5340 as our EVK with a 12 antenna array plate(4x4 with center 4 ones not being there). Our beacon uses nRF52833.
We used Nordic's sample codes- ...
Title: nRF52840 / OpenThread: how to inject custom IEEE 802.15.4 RX frames into the native receive path?
Hi,
I am working on a test setup around nRF52840, OpenThread,...
While configuring a scene, the blind device is not visible in the scene settings screen, so it is not possible to set or save the blind position as part of the scene.
Steps...
Hi all — I'm developing a custom nRF5340 development board (Raytac MDBT53-1M) and would value the community's honest read on whether it's worth producing.
The goal is...
I am trying to set a timer pulse at 500kHz and on every high pulse i want to do a read on another pin.
I have an IC HX711, that has a 24bit output MSB. every positive...
Hi,
im a beginner and i have problems to integrate the Homekit SDK in the Connect SDK.
Maybe anyone have a link to a tutorial?
The implementation by west has no effect...
Hi, Q1) I am facing an issue with the heap memory. I am using the Cjson_Parse function which uses quit a lot of memory. So I am wondering if there is a way to increase the...
Hello,
i m working on usbd example on nRF52
i have a problem that usbd stops sending data aftew few time. the port is still enabled but the data is not sent! any proposition...
I am trying to communicate with a sensor that has some interesting timing requirements for reading information from it, it requires ~100us delays between the address to read...
I want to calculate the power consumption used by many peripheral like GPIO, TWI, UART, SPI, RTC, SAADC. I can't find these information in nrf52840 PS v1.1
Because I don...
Hi, On my Windows 10 machine I've installed nRF Connect for Desktop (v3.7.0) and then used Toolchain Manager utility for installing nRF Connect SDK (v1.6.1). Afterward, navigating...
Hi,
I'm working on a project using BLE via s140, everything was working fine until I wanted to implement usb.
I created a blank project in order to validate the usbd then...
Hello, I have and audio source and i would need to divide it beetween two frequencies (<95Hz and >=95Hz).
Im trying this thing with a nRF52840 and i was looking at DSP libraries...
hi support team,
i have one question about DFU function question,:
in our ncs sdk , nrf5 desktop can dfu from hid feature(from configuration channel setting ), if it...
Hello,
I wanted to add uart in ble_custom_template project. I have added UART and FIFO Libraries in User include Libraries. Also i set the bits for uart in sdk_config.h...
Hi There,
So I get the Data from MPU9250 to nRF9160 DK with This Example zephyr/tree/master/samples/sensor/mpu6050
just want to know how to do it with Thingy91 I try...
Hi,
I have nRF52 dev boards. The device is programmed as a custom beacon. For saving the battery, the device send 3 advertisements at 300ms interval, then sleep for 10 seconds...
Hi I am working on nrf5340 direction finding example using nrfconnect zephyr v1.6.0-rc2. i had build example zephyr\samples\bluetooth\direction_finding_connectionless_tx for...
