Hey there!
I am facing a very frustrating issue, where my nRF54L15 (custom board) BLE peripheral just won't appear in mobile apps.
For example, right now I am trying to...
Hi all,
I'm deploying an nRF9160-based device in India and hitting the familiar "which SIM actually works here" wall. Looking for current (2026) experiences, since older...
Hi all,
I've built a custom nRF9151 board, which is successfully responding to the basic factory AT commands. It won't accept a CFUN=1 command though, presumably because...
Hello!
I think there is a problem in NCS v3.3.0. nRF54L target, sysbuild build with MCUboot and TF-M, partition layout coming from devicetree (SB_CONFIG_PARTITION_MANAGER...
Hi, I'm developing a keyboard-pcb with NRF52840. I'm doing this as a hobby and are not that experienced with integrated circuits. Anyway, I designed and produced a pcb, but...
Hello,
in cases where the LTE signal strength is extremely low, we observed that the LwM2M /4/0/2 RSRP rolls over from -128 to 127. We found that the nRF Connect SDK uses...
As part of the Bluetooth LE course we need to setup and install the nRF BLE sniffer for wireshark. I have followed the explained steps in the course to set up wireshark to...
Hello
I am trying to read a characteristics from my peripheral using my central. From what I read here, I have to use sd_ble_gattc_read(). Is it correct ? But I did not...
Hello
We have produced boards with a Telit module using the nRF52832 chip.
Our software developper have a lot of problems making the connexion and communication reliable...
Hello,
After a long war trying to connect MPU6050/MPU9250 to NRF52 DK with nrf52832 on board, I finally succeeded and I am getting values through UART.
But I have 3 problems...
Hi,
I would like to get the stored CCCD values of a bonded peer using pm_peer_data_load()
I am currently struggling with the format of the data returned by pm_peer_data_load...
Hello.I am a graduate student at Nanjing University of Posts and Telecommunications in China.My question is, does your company provide the source code of the Bluetooth mesh...
To the kind attention of Nordic support team,
we are doing ble bonding using passkeys.
We noticed that when starting the passkey phase, a ble connection event is generated...
I am not able to run commands with nrfjprog using the J-link Segger device
e.g. nrfjprog --family nrf52
I can do it only with the Keil or Segger UI environment
How can...
hello
right now i am sending 100 plus data per second i want to print millisecond at each data how can i acheive this is there any program in nordic or github i can use...
Hello
I am working on SDK v17, using nRF52832 (MDBT42Q) and MPU6050 sensor. I tried TWI_SCANNER because I thought there was a problem getting the value of MPU6050.
However...
I am reading a thermistor voltage divider from Vdd using the SAADC with a reference voltage of Vdd/4 and gain of 1/4. I thought that this would track Vdd so I wouldn't need...
Hi, the provisioning works and after that the dk is capable to get mesh messages but oddly enough a restart brokes this feature.
The error message is:
0x0c means BT_HCI_ERR_CMD_DISALLOWED...
Trying to install nrfutil on a system with Python 3.9 but it only installs the old version 5.2.0 which is broken on Python 3. This is the last version before the version check...
I use the internal LFCLOCK to drive my application. Sometimes, I need a more accurate clock to do time measurement. At startup, I can start the external crystal oscillator...
Hi,
I am trying to get Secure UART Bootloader to work and followed the steps mentioned here .
I generated the Keys and updated the dfu_public_key.c file in the project...
Hello,
I'm planning serial wire flash writing from custom board gpio to nRF52840 serial wire.
nRF52840 SWDIO/SWCLK/NRST are connected to a custom board GPIOs.
Is there...
