Hi,
I was looking at integrating a speaker in my design and i have a class d amplifier that takes in an analog signal which i want to feed directly from the chip. I wondered...
Hello,
I am using SDK v2.9.1 for a Bl653 (NRF52833) and was trying to use the Nordic Academy Example for how to setup the SPI bus. The Nordic Academy example states we must...
I'm currently working on configuring the nPM1300 used in our custom board. In the product spec v1.2, it supports 2 USB compliant current limits, IBUS at 100mA and IBUS at...
Hi,
I am currently trying to enable the GPIO output interrupt functionality on my nPM1300ek with an STM32. However, I am unable to get it work correctly(I was only able...
Hi,
What is the lowest possible current consumption for nrf52840 dongle dev board with zigbee ?
I'm using this for development and i'm getting 20-30uA in idle. Is it possible...
Hello, I am working on incorporating flash logging into an application that has a GRTC-driven EGU interrupt (capture/compare event). Here is where I am setting up the EGU...
We are experiencing some ESB link failures on the receiver end of our system: nrf54L15. After minutes to hours of use the receiver will stop getting data (we know the transmitter...
Hy,
i get two warnings from my c++-compiler (arm-none-eabi-g++ (GNU Tools for Arm Embedded Processors 7-2017-q4-major) 7.2.1 20170904) if I use the header cmsis_gcc.h in...
Hello
in the thread about NUS connection problems with TimeSync example ported to SDK16.0.0 Sigurd confirms a bug in the timeslot API.
Could you please be more specific...
Hi,
I am using nRF52832, SDK16.0
with SES
Is that nRF52832 have able to send timestamp through BLE. is that hardware able to calculate timestamp
will it act as REAL...
HI
my Version: SDK15.3,ble_app_template,custom board with nrf52832
I'm trying to load device name from fds when initial,
my goal is sending message to my board to change...
For some reason, it seems that I am not able to send any raw data with the BLE radio. I am able to configure the radio and start it successfully. However, the radio never...
Hi,I used Nrf52832 connect BMX055 with i2c, I use sdk nRF52_SDK_11.0.0 example examples\ble_peripheral\ble_app_cscs and add my code to read the BMX055,but when it work a short...
Hi Nordic,
i have a question regarding the emBuild.exe tool and the optimization level it will use during building a hex file. I'am using the following command combination...
Hello,
How can I determine the current consumption of Bluetooth 5 use nrf52832 soc with transmission at -4 dm when in the datasheet mentioned only the current consumption...
Hi,
I've just got an Arduino Nano 33 BLE with the NRF52480 chip on it.
I've been trying to manage the Pin configuration by setting the register values through the Arduino...
Hi,
I am using a NRF58240-dk pca10056 S140.
I have an external SD card device connected which, I am writing live sensor data to then advertising that data over a ble advertisement...
Hi ,
The device required to keep advertising during the connection established.
It is human interface device which mean it is peripheral device as well.
I would like...
Hello there,
A while ago I started developing on the nRF9160DK but I found an issue that I do not know how to solve by myself.
I used two SIM cards: the one from iBasis...
._build\nrf52832_xxaa_s132.axf: error: L6002U: Could not open file ..........\external\micro-ecc\nrf52_keil\armgcc\micro_ecc_lib_nrf52.lib: No such file or directory
Hi all,
Is there any sample sdk example for transferring audio file from nRF52840 to my mobile? Is it possible to transfer audio file through Nordic Uart Service? Thanks...
Hi,
I am developing a product based on nrf52840 soc, I need to write a softdevice, program hex file, bootloader on the chip. when I want to select them all in the nrf...
