The firmware always halts execution during boot after providing these logs:
26/05/22 10:38:33.925 89737.861 13892 0 E: Device id 00 00 00 does not match config 1f 16 01...
Hi Team,
Whether there is any configuration or option available to disable/eliminate signature verification during the boot process.
If disabling is not recommended...
Hi,
I am using NCS v3.3.0 and would like to implement the following setup:
Central: nRF52840 Dongle (connected to PC via USB)
Peripheral: nRF52833 acting as...
The at command documentation says that ENVEVAL is only available in system mode 2 (CFUN=2). Is there a reason why the command can't be run in any other mode? For example if...
Hi
The TWI driver has a twi_clear_bus() function but the TWIM does not.
I'm getting an I2C error, and need to do I2C soft reset. I'm doing this manually at moment but...
I recently completed a field-upgrade path from an nRF5 SDK 17.1 application (with the legacy Secure DFU bootloader) to a fresh NCS-based firmware stack, while preserving user...
Hi, I am trying to understand the Friend and LPN behaviour. For that I am refering to nRF sample application light" and "light_switch". Below is the setup details: 1. On one...
I am using RTT logging and it is interfering with USB HID data transfer. The host sends consecutive OUT packets and I print some logs after each one. I will miss a APP_USBD_HID_USER_EVT_OUT_REPORT_READY...
Hi,
We are using nRF52840 chipset with SDK 15.0.0 with Mesh implemetation.
1. We are provisioning the mesh node using the nRF mesh APP.
2. Then we are resetting the...
Hello,
I had been looking at BLE mesh documentation as well as the examples on the SDK and looks every node should have a dedicated function. generic on/off server controlling...
Hello!
I am trying to interface with some old hardware that communicates over a single data pin. I need to take in varying 32-bit packets and output the data that translates...
Hi all,
The chip we used is nRf52832, the version of SDK I used is nRF5_SDK_15.2.0_9412b96.
The problem is when I pair to windows 10, sometimes PM_EVT_PEER_DATA_UPDATE_SUCCEEDED...
Hi,
I am using i2c driver available with zephr as i2c master. This is working fine.
I want to change the pins to P0.02 for SCL and P0.03 for SDA. I see multiple questions...
Hello,
I am looking into the peer manager and the LESC module and have some question regarding what is possible to do with this.
Is it possible to manage the private...
Hi,
I am updating SDK version from 15.0 to 17. We are using nrf52840.
I would like to know if these are necessary to add, as they were added in some examples, and if so...
Hi,
i have a problem when using the ble_uart connected to Raspberry-pie withe Bluez.
after 40 seconds the connection is lost.
tried to use several examples, but most...
Hello Community I am starter in nrf51822 i want to know if anybody has code for interfacing with ADS1115 since i didn't got any of the post which would be helpful, please...
Hello,
Is there a particular test Nordic recommends to screen for latent failures in the BLE circuit? If one has access to an Anritsu MT8852B tester with Direct-Test-Mode...
Hi,
I am updating SDK version from 15.0 to 17.0.
In many examples PM_FLASH_BUFFERS was changed from 2 to 4? What is the meaning of this change? We have one peer always...
While exploring documentaion and trying to learn more about the DFU (and bootloader settings), I found info on how to generate the bootloader settings , which also explains...
