Hi,
I am developing a project where we wish to use part of the RRAMC memory for logging purpose. The documentation show that the data endurance of RRAMC in nRF54L15 chips...
I am using LVGL for simple Eink display UI, and trying to implement a simple if condition to check if the passed string argument is null as below:
If I only have btn1...
Nordic TS,
I've installed and begin to experiment with the DECT NR+ v1.1.1.0 FW. Initially, I'm noticing on obvious difference in the behavior of the dect_hello sample between...
I am trying to use the FIFO from the ADXL362 with in the Thingy:53. As I noticed there is now the Option to use ADXL362_STREAM. I just wanted to use the example from: https...
The specification for the nRF54L15 states that the typical current consumption for I_TIMER3 (TIMER10 running) is 240 mA/milliamps . The other timer values in the table are...
The Nordic Thingy:91X was initially unable to connect using certain SIMs (e.g., Airtel IoT) due to lack of NB-IoT support or no signal.
After switching to a Jio NB-IoT...
Hi to all,
I am trying to do a ZUTH (Zigbee unified test harness) test run, using the Silabs devices as golden devices (as per CSA recommendation) and nRF 52840 dongles...
I am working on a project that needs to be a ble central and peripheral. I based my development off the experimental/ble_central_and_peripheral/ble_app_hrs_rcs_relay however...
Dear Sirs, good afternoon
I am working in a design that includes an nRF52840 as main processor.
I need to know if it is possible to have the following peripherals implemented...
Hi,
How do we fuse the debug port on nRF9160? The purpose is to block all access and the ability to erase all from outside.
This is my understanding:
From debugger...
My nrf9160 connects to AWS when using the AWS FOTA example. However, when I start the custom job as setup from the following link:
https://developer.nordicsemi.com/nRF_Connect_SDK...
Hi,
I have a board that emits 0x1818 (Cycling Power) using the nrf51422 chip and firmware using S310 and so forth. Working great :)
Now I just found some strange things...
Hello guys!
We are using nRF9160 SiP module to transfer MQTT messages to AWS IoT. So far, thanks to the cloud_client example and your documentation from here , we were able...
Hello,
I am using Segger Embedded Studio (SES) to develop with the nRF5340 BLE chip. From what I've read, the nRF Connect SDK and Zephyr OS is not tailored for use with...
Hi,
I would like to check my understanding of PSM. Currently, using the AT Client on the local NB-IoT network, I can see that the device is entering PSM after 3 minutes...
Hi, I'm looking for a simple example on how to implement I2C. I've built I2C on my various FPGA's, implemented I2C on various AVR based chips from special function registers...
Good afternoon,
I first devoloped my app based on the nRF52840 (SDK 15.2; S140 V.6.1.0) and it was perfectly working with or without bonds.
After that, and following what...
I've been doing some development on the nRF Mesh platform for the nRF52832 chipset and I'm relying on the Mesh DFU protocol to update my deployed units. Recently I've been...
We need to know what the total internal capacitance and inductance is for the nRF9160 SIP to comply with intrinsic safety certification. Can anyone point me to this information...
Hi, We have developed a custom board. We can upload code using nrf52840 sdk-ble stack. We can read NRF_LOGS. However when we test with the ble_app_blinky that works fine with...
