I'm writing a wav file from the nrf52840 board to the nor flash w25q128jv with a capacity of 16mb but it seems that I can only operate on the first 2mb, even when dividing...
Is there an AT command (For modem firmware >= 2.0.2) that can be used to validate whether the LTE modem can communicate with an external MIPI RFFE switch (for example on a...
Can Nordic share specific instructions on how to enable hardware tracing?
I've received the following patch from Tomasz, however I still see "trace clock missing" in Ozone...
Hi
our last product is based on nRF5340 and now we start a new design based on nRF54H20, and its essential for our design, i checked alot but there is no datasheet, reference...
just passed Cellular IoT Fundamentals while I was waiting for my nrf9151dk to be delivered... Now that I have the DK I can't get the dk to be provisioned...
I couldn't get...
NCS currently has a nice feature where the firmware versions are printed in the boot banner:
Is there a config option to also enable printing the nRF91 modem firmware...
Dear all,
after cutting the SB bridge to the QSPI chip and close the ones to get the pin free and disabled also qspi inside the nRF52840dk_nrf52840.overlay file I'm unable...
I am having a problem running MQTT_Simple on my nRF9160 DK.
The COM Port shows the following:
***** BUS FAULT ***** Precise data bus error BFAR Address: 0x4002a514 **...
Hi.
I am using the nrf9160 with the latest firmware and with all the instructions followed, I get this error . Faulting instruction address = 0x3648 Fatal fault in ISR!...
Hi,
I am working on mesh bluetooth using nrf52832 with PCA10040 , I used example from nrf5_SDK_for_Mesh_v2.0.1_src , my questions are
1.How many bytes(Max and min) can...
Our device allows only one device to pair and delete the original pairing information when there is a new device paired. Restore the original pairing information if there...
Hi,
I am using the nrf52832 dk for my project.
I am using the RX characteristic of the NUS example to send data from the phone to the dk.
In the same code i am also...
I tried to build the "nRF5_SDK_15.1.0_a8c0c4d\examples\crypto\nrf_crypto\aes\aes_all_cli\pca10056\blank" source code but I got the following error,
.\_build\nrf52840_xxaa...
Hello,
While i am trying to find the definition of SER_REQ_ENC_BEGIN(SD_BLE_GAP_ADV_START); it is there in the file ble_gap_app.c
When i right click on that function...
What is the difference between nrf5232, 1.8V and 3.3V power supplies? What should watch out for when replacing a 3.3V power supply with a 1.8V power supply?
Hi,
I'm developing a central application and I want my central to read the device name characteristic from 3rd-party peripherals. I do not know the length of the data in...
Hi,
I've been trying to develop a custom service for a Bluetooth application. This custom service (called ble_dts - Data Transfer Service) has two characteristics - Spectrum...
Daer sir or madam
I am the personal software engineer and want to check and receive the best answer about my question. If I use BLE to connect the both smartphone and device...
My hardware only has one spi slave and one spi master. So can I just set the spi slave miso pin as output in spis_init function? If can not, can I set the pull down resistor...
Hello, I am trying the nRF9160 DK for the first time and when I try to connect my DK to my laptop and select my device in the nRF Connect Programmer it shows the error highlighted...
Hello, I am trying the nRF9160 DK for the first time and when I try to connect my DK to my laptop and select my device in the nRF Connect Programmer it shows the error highlighted...
