I'm looking into a rare issue on the BBC micro:bit V2 which uses the nRF52833 as its (application) microcontroller. I used to be familiar with some CPUs from the 80s but my...
Hi everyone,
I'm working with the nRF9160 and trying to configure P0.19 as the UART TX pin using Zephyr. Here's the configuration I used in the device tree:
uart1_default...
I have shifted from silicon labs for BLE project. In Si labs we have burn BLE bootloader and BLE application separately. Do i need to do the same here in nrf controller? If...
Hello,
I am using nRF Connect SDK v3.0.1, together with the Find My add-on. Test case TCG013 of the Find My Network Self-Certification Test Cases R1.7 is failing on the...
I am unable to detect any i2c device when connected to the Nordic nRF54L15 DK kit. I have change the voltage from 1.8v to 3.3v and Tried and explore other pins in Port 0 and...
HI: D:\ncs\v3.0.0\nrf\samples\bluetooth\peripheral_uart Using the nrf54l15DK board can run peripheral_uart examples,connection is disconnected. However, when I use the nrf54l05...
Hi,
I'm working on software for a design incorporating an Ezurio module that uses an NRF54L15 chip.
I'm currently using the peripheral_uart example as a base for early...
Hi, i am trying to add additional payload to the Mesh Light Switch example. However, i modified all structs and it came down to the status_handle() function inside generic_onoff_client...
Hello,
I am using nRF52832, SDK_15.3.0, S132 SoftDevice and Segger for flashing the image.
After wakeup from System OFF (due to GPIO event), I want to validate / debounce...
On the nrfCloud, when you clicked on a device (nrf9160DK), the previous version of the interface would show how much data was used of the "available" data associated with...
We are developing a cycling application and are currently using a variety of ARM processors with BLE capability. We require to add ANT+ capability to read Hear Rate monitor...
Hello,
I'm developping an android application for detecting falls.
I will use accelerometer's values for find the g constant.
But i recover bad values.
this is my...
Without doubt there is a new variation of software emerging:
We are all familiar with Firmware and Software, however I really feel the need to coin the term "Whisper Ware...
I am experiencing a problem where behaviour after an sd_nvic_SystemReset() differs from behaviour after a power-on reset, and this difference causes failures in the softdevice...
Hi, I see there are several questions related to using GPS pulse per second signals for synchronization between devices, but I can't see the responses to some of the questions...
Hi,
I am using Uart1 on nrf52840. This is implemented using nrf_serial library. I have set buffer size to say 10, so event occurs on every 10 bytes reception. Now I want...
Hi,
I have been looking at the Nordic examples and I found them to be pretty slow with the handlers being the bottleneck as opposed to the actual hardware. I was wondering...
I'm developing an application to support multiple concurrent central-and-peripheral connections. It's a bit messy but is just about working. At the moment I'm using SDK 9...
Hello All,
I am facing problem in compiling uECC.c on windows10.
Please any one tell me what is the procedure to build and compile that file.
I have tried on the compiler...
I have a question about the relationship between SDK and sotfDeivce.
I want to use nRF SDK v15.3.0. I know that the document has the following description.
This version...
Hi,
I have no idea why the original libraries are giving me errors such that I didn't change anything from the driver.
Please let me know if I need to do anything in...
Is there a set of directions for configuring the peripherals for the nRF9160 SPM.
I need to change the default configuration shown in the SPM sample.
I tried editing the...