In my circuit I have a MOSFET which disconnects the battery. There is a GPIO pin which turns this device on and I'm using regulator-fixed to drive it during start-up. A short...
We are currently using ncs 2.9.0 on an nRF5340. We use the BT_HCI_OP_VS_READ_VERSION_INFO to determine at runtime what version of the BLE stack is present. This information...
Hi I'm trying to load a custom board with nrf9160 with the Serial LTE Modem, and route the AT commands to the UART from a coprocessor (ESP32C3) I have followed the guide on...
Hello,
we have a working system on the nrf9161 that works without zephyr. We have our own secure firmware that successfully uses the cc310 after we start the actual application...
Keep hitting my head on this inconvenient workflow.
Edit build config
Select target custom board
Build config
All OK
Edit config again
Target board has been...
I have used the Programmer previously with success. I am attempting to program the Dongle (10059) with a slightly modified version of ble_nusc_usb_dongle. Although it claims...
H ello Nordic team,
I'v found a bug on mqtt sample (using both ncs 3.0.0 and 2.6.1).
Description
Settings CONFIG_MQTT_SAMPLE_TRANSPORT_CLIENT_ID and trying to connect...
Based on multi-protocol add private agreement GZLL matching procedure, no matching success;But separate GZLL agreement can be successful, not any way to solve this problem...
Hey devs!
We'd like to add additional fields in the manifest.json when generating (or after generating) the zip file for DFU. We need these fields to make additional compatibility...
Hello,
I am using the nrf 52 dk with the soft 3.00. I am doing the Beacon Transmitter Sample Application from infocenter.nordicsemi.com/index.jsp.
I was able to compile...
Hi
I am using nrf52832 QFAA-R.
I wanted to know if there is a difference between SPIM current when SPIM is:
stopeed
started but not active.
Thanks
Yar...
While analyzing the current consumption of my nRF52832 Dev Kit I noticed that the system on low power current was significantly higher than expected. To further investigate...
i have connected the swdio , swclk , vcc , gnd , reset with the respective pins of the nrf52SDK ,but when am debug the nrf52sdk , am getting the following error.
ERROR...
Hi all,
I am testing out the BLE_APP_UART example on a NRF52DK and I am using SDK13.0 (PCA10040, S132).
I have change the app advert timeout to be 10 seconds.
I am...
I am trying to combine both the SAADC and BLE libraries to be able to read a value from my sensor on the analog pin and then send it over Bluetooth LE to a central dongle...
I plan to merge the protocol sack and the application. At the same time download in batch to 52832 by using the SWD. But the tool(nRFgo Studio) offered officially is not fit...
Using existing examples in SDK13, I prepared ADC sampling app which works fine in ESB TX mode. Works well sending frames at 10ksps, and I can also put it to 'standby mode...
Hello! I have to connect some microphones (adafruit MAX9814) to a nrf52 board and I have to choose some beacons. My idea is to have a tiny solar panel that charges a capacitor...
I have a custom nrf52832 board. I have changed the UART TX and RX pins to P0.3 and P0.4 respectively. If the pins are floating, then nrf52832 stops advertising,If something...
I use example ble_app_hrs_pca10040_s132 with SDK12.2.0 to test bonding function.It works as a server and it is bound by client. But I fail to bond. It seems that example has...
Hello,
I try to declare two instrances of TWI0 and SPI1, and I include the both sdk_config (sdk_config_spi and sdk_config_twi) in the same file, but I always get the error...
