Dear Nordic,
I have a Thingy91x. I tried flashing the nRF9151 SoC on the device but ran into error messages. I realized that the nRF53/nRF91 switch was in the nRF53 position...
im looking for a developer that can help me work with the NTN functionality of the 3GPP release 17 of the NRF9151-DK so if you are interested please write to me at eric@zerocool...
Hi everyone.
I am using Visual Studio Code. When i try to compile a simple blink_pwm project, I could not. I am sending output in terminal. What is the main problem and...
Greetings, everyone, I have encountered a configuration(?) problem while trying to setup a lab for a BLE course I am teaching.
The idea is to showcase the vulnerability...
Since NCS 3.0.1 I get the following warning:
warning: Deprecated symbol DEPRECATED_UART_NRFX_UARTE_LEGACY_SHIM is enabled.
... as far as I can see I have not enabled this...
So whatever I try, the only way to get my idle current consumption to an acceptable low value is to set CONFIG_SERIAL=n in my configuration. But then I don't get printk functionality...
Hey, I am working with the Matter light bulb sample from the 2.9.1 SDK, which I have modified to support the occupancy cluster. (nRF-52840 and nRF-52840DK)
This worked fine...
Please excuse my ignorance, My company is designing in the nRF52832 for our first product using both ANT and BLE. From looking at the documentation on thisisant.com there...
I've got a strange problem with updating my Magnet-Characteristic.
I use a service with 4 characteristics (Gyro, Acc, Mag and Temp Values) and update them on a timer base...
Hello,
Two issues want to ask, after tried the BLE_NUS example code.
From other posts, still does not exist clear solution (example, pictures) ?
Sure has an application...
Hello,
I am working with the uart module. While configuring the uart I encounter 2 issues.
First when in the uart_init function the pin for uart output is configured...
Hi,
I am using nrf51822(128k), SD 6.0, SDK 5.2.
I found that nrf uart v2.0 app will add a "0x0A" at the end of data that I want to send.
How can I remove this?
Thank...
Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
I've never used Gnu's GCC before, but after 20 hours of trying and failing to install it on my macbook, I'm finding a shining hatred. I've downloaded their exhaustive list...
I migrated to nrf52 and countering some problems.
I am trying to sample 4 pins every 2ms with SAADC.
I started with Example here .
I simply changed
uint32_t ticks...
I've got a gyro I want to read some data from, but I don't know the values and can't verify if they got read correctly. When does nrf_drv_spi_transfer start to read?
i...
Hi, i;m trying to build the "nrf52-ble-app-lbs" example which i downloaded from git hub github.com/NordicSemiconducto....
I followed the instructions in the README file...
I'm thinking about changing ADC resolution during operation.
What I want to do is:
start
・Operate in 8bit ADC(normal time)
↓
・Operate in 10bit ADC(particular...
I want to use NRF51 DK to sample 2 analog signal continuously (300Hz) and send it to a smartphone using BLE.
I need advice on
Which nrf example to use to code my DK...
I've run out of space in my attribute table. No problem, I'll just make it bigger with ble_enable_params.gatts_enable_params.attr_tab_size .
The easiest way to do this...
