Hi all,
I'm deploying an nRF9160-based device in India and hitting the familiar "which SIM actually works here" wall. Looking for current (2026) experiences, since older...
Hi all,
I've built a custom nRF9151 board, which is successfully responding to the basic factory AT commands. It won't accept a CFUN=1 command though, presumably because...
Hello!
I think there is a problem in NCS v3.3.0. nRF54L target, sysbuild build with MCUboot and TF-M, partition layout coming from devicetree (SB_CONFIG_PARTITION_MANAGER...
Hi, I'm developing a keyboard-pcb with NRF52840. I'm doing this as a hobby and are not that experienced with integrated circuits. Anyway, I designed and produced a pcb, but...
Hello,
in cases where the LTE signal strength is extremely low, we observed that the LwM2M /4/0/2 RSRP rolls over from -128 to 127. We found that the nRF Connect SDK uses...
As part of the Bluetooth LE course we need to setup and install the nRF BLE sniffer for wireshark. I have followed the explained steps in the course to set up wireshark to...
The at command documentation says that ENVEVAL is only available in system mode 2 (CFUN=2). Is there a reason why the command can't be run in any other mode? For example if...
It looks like NFC_T4T_EVENT_NDEF_UPDATED gets passed as the event attribute in the nfc_callback function whenever a new NDEF message is written.
Is this expected behavior...
Hi,
I have an aconno module ( http://aconno.de/acn52832/) and I am trying to program it via DK52.
I wired the module as follows:
Module Vcc (pin 12) -> DK52 VDD...
Hi all,
I am trying to get the ble template of SDK12.2 working in eclipse using a managed makefile. The softdevice I use is s132 v3.0.0. The board is an evaluation kit...
Hi Nordic,
I'd like to know what the maximal current draw from the internal REG0 is to power external components. The only thing I could find in the datasheet that says...
HEllo,
I am trying to compile for the nrf52 one of the examples that are included in its SDK12.2, to be precies, I am using experimental_ble_app_blinky_pca10040_s132 ,...
I have noticed that the reference schematic (the original if you can call it that, not the 1v8 or DC/DC) for nRF51x22-QFAA, QFAB and QFAC have different value capacitors and...
Hello,
I cannot use the nRF Sniffer because it is always crashing. This is a confirmed bug in the Software and the OSX client written is working flawlessly.
I have experimented...
Hello,
I am newbie with KEIL/SEGGER, I have been following this tutorial to compile the example experimental_ble_app_blinky_pca10040_s132 for my nrf52 chip, the project...
Hello,
I am using sdk 12.2.2 and nrf51 dev kit. I am trying to upload ble_app_gls example code over the air to nrf51 dev kit. I can find only secure_dfu code in the sdk....
I am considering build some of my own shields to interface with the nRF52DK for the 832 and 840. I am curious how I should use header P5 with the shield detect pin. Should...
Hello,
I am trying to implement my custom service with NUS. I have gone through almost all the solutions presented on this forum.
Observations:
The board does...
Hi,
I need to be able to change the GAP parameters of my connection for only a short period of time to save battery life but have high throughput when I need it. My firmware...
Our workshop is using custom PCBs for other manufacturer's developer kits, and I'd like to do a similar shield for our nRF51-DK boards. Can anyone provide a KiCad project...
